manual:demos:dk_tm4c123g_iar
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
manual:demos:dk_tm4c123g_iar [2014/03/10 10:27] voorburg created |
manual:demos:dk_tm4c123g_iar [2023/12/04 22:42] (current) voorburg [Supported firmware update interfaces] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== ARM-CM4 TM4C Texas Instruments DK-TM4C123G IAR EWARM ====== | ====== ARM-CM4 TM4C Texas Instruments DK-TM4C123G IAR EWARM ====== | ||
| + | |||
| + | ===== Supported firmware update interfaces ===== | ||
| + | |||
| + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ | ||
| + | | Yes | No | Yes | No | Yes | No | | ||
| ===== Development Environment ===== | ===== Development Environment ===== | ||
| Line 10: | Line 15: | ||
| To compile the demo programs you can use the [[http://www.iar.com/|IAR Embedded Workbench for ARM]] development environment. | To compile the demo programs you can use the [[http://www.iar.com/|IAR Embedded Workbench for ARM]] development environment. | ||
| - | |||
| ===== Building and programming the Bootloader ===== | ===== Building and programming the Bootloader ===== | ||
| Line 22: | Line 26: | ||
| * \Target\Demo\ARMCM4_TM4C_DK_TM4C123G_IAR\**Boot**\bin\**openblt_dk_tm4c123g.bin** | * \Target\Demo\ARMCM4_TM4C_DK_TM4C123G_IAR\**Boot**\bin\**openblt_dk_tm4c123g.bin** | ||
| - | ===== Configuring Microboot ===== | + | ===== Building the Demo Program ===== |
| - | The Microboot utility needs to be configured to connect to the correct COM-port and to communication at the correct baudrate: | + | |
| - | + | ||
| - | * Start Microboot by double-clicking "\Host\**MicroBoot.exe**". | + | |
| - | * Click the "**Settings**"-button and select "**OpenBLT using UART**" from the dropdown box. | + | |
| - | * Click the "**Options**"-button to configure the communication parameters. | + | |
| - | * Select the PC's **COM-port** that the board is connected to. | + | |
| - | * Set the baudrate to **57600** bits/sec. | + | |
| - | + | ||
| - | Once you saved the settings by clicking the "**OK**"-button twice, you can close Microboot by clicking the "**Cancel**"-button on the main screen. Microboot is now ready for action! | + | |
| - | + | ||
| - | ===== Building and downloading the Demo Program ===== | + | |
| When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (tm4c123g.eww) is located at: \Target\Demo\ARMCM4_TM4C_DK_TM4C123G_IAR\**Prog**\ide\. Once opened, select Project->Rebuild All from the menu to compile all the demo program sources and link the together into the final executable. | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (tm4c123g.eww) is located at: \Target\Demo\ARMCM4_TM4C_DK_TM4C123G_IAR\**Prog**\ide\. Once opened, select Project->Rebuild All from the menu to compile all the demo program sources and link the together into the final executable. | ||
| Line 39: | Line 32: | ||
| * \Target\Demo\ARMCM4_TM4C_DK_TM4C123G_IAR\**Prog**\bin\**demoprog_dk_tm4c123g.srec** | * \Target\Demo\ARMCM4_TM4C_DK_TM4C123G_IAR\**Prog**\bin\**demoprog_dk_tm4c123g.srec** | ||
| - | To download this **demoprog_ek_lm3s6965.srec** file to the remaining flash memory using the bootloader, start the **Microboot** program and click the "**Browse**"-button. Browse to the "\Target\Demo\ARMCM4_TM4C_DK_TM4C123G_IAR\**Prog**\bin\" directory and select the **demoprog_dk_tm4c123g.srec** file to start the download. | + | ===== Firmware update procedure ===== |
| - | + | To download the demo program \Target\Demo\ARMCM4_TM4C_DK_TM4C123G_IAR\**Prog**\bin\**demoprog_dk_tm4c123g.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | |
| - | {{:manual:demos:dk_tm4c123g_download.gif?|}} | + | |
| - | + | ||
| - | Once the download completed, the newly programmed software will be started by the bootloader. You can verify this by checking that the status LED blinks periodically. Congratulations! That's all there is to using the bootloader. | + | |
| - | + | ||
| - | ===== Firmware updates from SD-card ===== | + | |
| - | In addition to the previously described update procedure with Microboot, the bootloader demo is configured for making firmware updates from an SD-card. The procedure is: | + | |
| - | + | ||
| - | - Insert the SD-card into your PC and store the firmware file **demoprog_dk_tm4c123g.srec** on it. | + | |
| - | - Insert the SD-card into the card holder on the microcontroller board. | + | |
| - | - Reset the microcontroller to start the firmware update. Once done, the newly programmed firmware is automatically started. | + | |
| - | + | ||
| - | The bootloader demo is configured to output log messages to a serial terminal. This enables you to view the progress of the firmware update with a terminal program such as Putty. The communication settings are the same as those described above in section //Configuring Microboot//. Additionally, the log messages are written to a file called **bootlog.txt** on the SD-card, which can optionally be checked for verification purposes. | + | |
| - | {{:manual:demos:tm4c_sdcard_firmware_update_logging.gif?|}} | + | * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] |
| + | * [[manual:usb_demo|Firmware updates using the USB communication interface]] | ||
| + | * [[manual:sdcard_demo|Firmware updates from SD-card]] | ||
manual/demos/dk_tm4c123g_iar.1394443653.txt.gz · Last modified: 2019/09/24 22:13 (external edit)
Page Tools
