This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
manual:demos:ek_lm3s6965_gcc [2017/08/16 15:39] voorburg |
manual:demos:ek_lm3s6965_gcc [2023/12/04 22:41] (current) voorburg [Supported firmware update interfaces] |
||
---|---|---|---|
Line 3: | Line 3: | ||
===== Supported firmware update interfaces ===== | ===== Supported firmware update interfaces ===== | ||
- | ^ UART ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ |
- | | Yes | No | No | Yes | Yes | | + | | Yes | No | No | Yes | Yes | No | |
===== Development Environment ===== | ===== Development Environment ===== | ||
Line 10: | Line 10: | ||
{{:manual:demos:ek_lm3s6965.jpg?200 |}} | {{:manual:demos:ek_lm3s6965.jpg?200 |}} | ||
- | This demo is targeted towards the [[http://www.ti.com/tool/ek-lm3s6965|Texas Instruments LM3S6965 Ethernet]] evaluation kit, with 256 kB internal Flash EEPROM and 64 kB internal RAM. | + | This demo is targeted towards the Texas Instruments LM3S6965 Ethernet evaluation kit, with 256 kB internal Flash EEPROM and 64 kB internal RAM. |
To program the bootloader into the internal flash on the LM3S6965 microcontroller, the LM Flash Programmer utility was used in combination with the In-Circuit Debugger Interface (ICDI), that is available on the board. However, this is not required if you have another means of programming the internal flash. | To program the bootloader into the internal flash on the LM3S6965 microcontroller, the LM Flash Programmer utility was used in combination with the In-Circuit Debugger Interface (ICDI), that is available on the board. However, this is not required if you have another means of programming the internal flash. | ||
Line 29: | Line 29: | ||
Before the bootloader can be used, it needs to be built and programmed into the LM3S6965's internal flash memory. The steps in this section only need to be done once. | Before the bootloader can be used, it needs to be built and programmed into the LM3S6965's internal flash memory. The steps in this section only need to be done once. | ||
- | Batch files are added to aid in building the software program. First clean the bootloader program by double-clicking the file "\Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\**Boot**\cmd\**clean.bat**". Next, build the bootloader program by double-clicking the file "\Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\**Boot**\cmd\**build.bat**". The output should look like: | + | To build the bootloader, open a command prompt in directory **\Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\Boot\** and run the command: |
+ | |||
+ | <code> | ||
+ | make clean all | ||
+ | </code> | ||
+ | |||
+ | The expected output is: | ||
<code> | <code> | ||
Line 48: | Line 54: | ||
===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
- | Batch files are added to aid in building the demo program. First clean the demo program by double-clicking the file "\Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\**Prog**\cmd\**clean.bat**". Next, build the demo program by double-clicking the file "\Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\**Prog**\cmd\**build.bat**". The output should look like: | + | To build the user program, open a command prompt in directory **\Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\Prog\** and run the command: |
+ | |||
+ | <code> | ||
+ | make clean all | ||
+ | </code> | ||
+ | |||
+ | The expected output is: | ||
<code> | <code> | ||
Line 67: | Line 79: | ||
To download the demo program \Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\**Prog**\bin\**demoprog_ek_lm3s6965.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | To download the demo program \Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\**Prog**\bin\**demoprog_ek_lm3s6965.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | ||
- | * [[manual:uart_demo|Firmware updates using the UART communication interface]] | + | * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] |
* [[manual:net_demo|Firmware updates using the TCP/IP communication interface]] | * [[manual:net_demo|Firmware updates using the TCP/IP communication interface]] | ||
* [[manual:sdcard_demo|Firmware updates from SD-card]] | * [[manual:sdcard_demo|Firmware updates from SD-card]] | ||