User Tools

Site Tools


manual:demos:ek_lm3s6965_gcc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:demos:ek_lm3s6965_gcc [2017/08/16 15:40]
voorburg [Building and programming the Bootloader]
manual:demos:ek_lm3s6965_gcc [2020/02/06 16:44] (current)
voorburg
Line 3: Line 3:
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
  
-UART           ^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^+RS232          ​^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^
 | Yes            | No              | No           | Yes           | Yes          | | Yes            | No              | No           | Yes           | Yes          |
  
Line 10: Line 10:
 {{:​manual:​demos:​ek_lm3s6965.jpg?​200 |}} {{:​manual:​demos:​ek_lm3s6965.jpg?​200 |}}
  
-This demo is targeted towards the [[http://​www.ti.com/​tool/​ek-lm3s6965|Texas Instruments LM3S6965 Ethernet]] evaluation kit, with 256 kB internal Flash EEPROM and 64 kB internal RAM.+This demo is targeted towards the Texas Instruments LM3S6965 Ethernet evaluation kit, with 256 kB internal Flash EEPROM and 64 kB internal RAM.
  
 To program the bootloader into the internal flash on the LM3S6965 microcontroller,​ the LM Flash Programmer utility was used in combination with the In-Circuit Debugger Interface (ICDI), that is available on the board. ​ However, this is not required if you have another means of programming the internal flash. To program the bootloader into the internal flash on the LM3S6965 microcontroller,​ the LM Flash Programmer utility was used in combination with the In-Circuit Debugger Interface (ICDI), that is available on the board. ​ However, this is not required if you have another means of programming the internal flash.
Line 54: Line 54:
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-Batch files are added to aid in building ​the demo program. First clean the demo program by double-clicking the file "​\Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\**Prog**\cmd\**clean.bat**"​. Next, build the demo program by double-clicking the file "\Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\**Prog**\cmd\**build.bat**"​. ​The output ​should look like:+To build the user program, open a command prompt in directory ​**\Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\Prog\** ​and run the command: 
 + 
 +<​code>​ 
 +make clean all 
 +</​code>​ 
 +  
 +The expected ​output ​is:
  
 <​code>​ <​code>​
Line 73: Line 79:
 To download the demo program \Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\**Prog**\bin\**demoprog_ek_lm3s6965.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: To download the demo program \Target\Demo\ARMCM3_LM3S_EK_LM3S6965_GCC\**Prog**\bin\**demoprog_ek_lm3s6965.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:
  
-  * [[manual:uart_demo|Firmware updates using the UART communication interface]]+  * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]]
   * [[manual:​net_demo|Firmware updates using the TCP/IP communication interface]]   * [[manual:​net_demo|Firmware updates using the TCP/IP communication interface]]
   * [[manual:​sdcard_demo|Firmware updates from SD-card]]   * [[manual:​sdcard_demo|Firmware updates from SD-card]]
  
  
manual/demos/ek_lm3s6965_gcc.1502890812.txt.gz · Last modified: 2019/09/24 22:14 (external edit)