manual:demos:evbplus_dragon12p_codewarrior
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
manual:demos:evbplus_dragon12p_codewarrior [2013/10/09 15:48] voorburg [Development Environment] |
manual:demos:evbplus_dragon12p_codewarrior [2023/12/04 22:38] (current) voorburg [Supported firmware update interfaces] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== EVBplus Dragon12-plus (Freescale HCS12DG256) Codewarrior ====== | ====== EVBplus Dragon12-plus (Freescale HCS12DG256) Codewarrior ====== | ||
| + | |||
| + | ===== Supported firmware update interfaces ===== | ||
| + | |||
| + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ | ||
| + | | Yes | Yes | No | No | No | No | | ||
| ===== Development Environment ===== | ===== Development Environment ===== | ||
| Line 9: | Line 14: | ||
| To program the bootloader into the internal flash on the HCS12DG256 microcontroller, the [[http://www.pemicro.com/products/product_viewDetails.cfm?product_id=33| P&E Micro USB BDM Multilink]] interface was used. However, this is not required if you have another means of programming the internal flash. | To program the bootloader into the internal flash on the HCS12DG256 microcontroller, the [[http://www.pemicro.com/products/product_viewDetails.cfm?product_id=33| P&E Micro USB BDM Multilink]] interface was used. However, this is not required if you have another means of programming the internal flash. | ||
| - | To compile the demo programs you can use the [[http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=CW-SUITE-SPECIAL&tid=CWH|Freescale Codewarrior for HCS12(X)]] development environment. | + | To compile the demo programs you can use the [[https://www.nxp.com/support/developer-resources/software-development-tools/codewarrior-development-tools/codewarrior-legacy/codewarrior-development-suite-special:CW-SUITE-SPECIAL|Codewarrior Development Studio for HCS12(X)]] development environment. |
| + | |||
| + | ===== Building and programming the Bootloader ===== | ||
| + | |||
| + | Before the bootloader can be used, it needs to be built and programmed into the HCS12DG256's internal flash memory. The steps in this section only need to be done once. | ||
| + | |||
| + | When using Freescale Codewarrior, simply open the project from within Codewarrior and select //Project->Make// from the menu. The project file is located at: \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Boot**\ide\ | ||
| + | |||
| + | In case of build errors, refer to the information in section [[manual:demos:evbplus_dragon12p_codewarrior#resolving_build_errors|resolving build errors]]. | ||
| + | |||
| + | The bootloader program is now ready to be programmed into the internal flash memory of the HCS12DG256. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports: | ||
| + | |||
| + | * \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Boot**\bin\**openblt_evbplus_dragon12p.abs** | ||
| + | * \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Boot**\bin\**openblt_evbplus_dragon12p.abs.s19** | ||
| + | |||
| + | ===== Building the Demo Program ===== | ||
| + | |||
| + | When using Freescale Codewarrior, simply open the project from within Codewarrior and select //Project->Make// from the menu. The project file is located at: \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Prog**\ide\ | ||
| + | |||
| + | The output file is | ||
| + | |||
| + | * \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Prog**\bin\**demoprog_evbplus_dragon12p.abs.sx** | ||
| + | |||
| + | ===== Firmware update procedure ===== | ||
| + | |||
| + | To download the demo program \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Prog**\bin\**demoprog_evbplus_dragon12p.abs.sx** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | ||
| + | |||
| + | * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] | ||
| + | * [[manual:can_demo|Firmware updates using the CAN communication interface]] | ||
| + | |||
| + | |||
| + | ===== Resolving Build Errors ===== | ||
| + | |||
| + | When building the demo binaries for the first time, build errors might occur caused by CodeWarrior projects not correctly dealing with relative directories and having source-files in a project that have the same name as source-files in the library path. These errors are quickly resolved by removing the file from the project and adding them again. | ||
| + | |||
| + | Here is a list of encountered build errors and the solution of resolving the error: | ||
| + | |||
| + | * Could not open object file '.Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\Boot\ide\hcs12_Data\Standard\ObjectCode\datapage.c.o' | ||
| + | * Delete the datapage.c file from the Boot\lib folder in the project and add it again. The source file is located at \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\Boot\lib | ||
| + | |||
| + | * Could not open object file '.Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\Boot\ide\hcs12_Data\Standard\ObjectCode\mc9s12dg256.c.o' | ||
| + | * Delete the mc9s12dg256.c file from the Boot\lib folder in the project and add it again. The source file is located at \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\Boot\lib | ||
| + | |||
| + | * Cannot open .\Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\Boot\ide\hcs12_Data\Standard\ObjectCode\cstartup.c.o | ||
| + | * Delete the cstartup.c file from the Source\HCS12\CodeWarrior folder in the project and add it again. The source file is located at \Target\Source\HCS12\CodeWarrior | ||
| + | * Link error: Symbol AssertFailure in file .Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\Boot\ide\hcs12_Data\Standard\ObjectCode\main.c.o | ||
| + | * Delete the assert.c file from the Source folder in the project and add it again. The source file is located at \Target\Source | ||
manual/demos/evbplus_dragon12p_codewarrior.1381326518.txt.gz · Last modified: 2019/09/24 22:13 (external edit)
Page Tools
