manual:demos:evbplus_dragon12p_codewarrior
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
manual:demos:evbplus_dragon12p_codewarrior [2015/05/22 18:05] 127.0.0.1 external edit |
manual:demos:evbplus_dragon12p_codewarrior [2023/12/04 22:38] (current) voorburg [Supported firmware update interfaces] |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ===== Supported firmware update interfaces ===== | ===== Supported firmware update interfaces ===== | ||
| - | ^ UART ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | + | |
| - | | Yes | Yes | No | No | No | | + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ |
| + | | Yes | Yes | No | No | No | No | | ||
| ===== Development Environment ===== | ===== Development Environment ===== | ||
| Line 13: | Line 14: | ||
| To program the bootloader into the internal flash on the HCS12DG256 microcontroller, the [[http://www.pemicro.com/products/product_viewDetails.cfm?product_id=33| P&E Micro USB BDM Multilink]] interface was used. However, this is not required if you have another means of programming the internal flash. | To program the bootloader into the internal flash on the HCS12DG256 microcontroller, the [[http://www.pemicro.com/products/product_viewDetails.cfm?product_id=33| P&E Micro USB BDM Multilink]] interface was used. However, this is not required if you have another means of programming the internal flash. | ||
| - | To compile the demo programs you can use the [[http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=CW-SUITE-SPECIAL&tid=CWH|Freescale Codewarrior for HCS12(X)]] development environment. | + | To compile the demo programs you can use the [[https://www.nxp.com/support/developer-resources/software-development-tools/codewarrior-development-tools/codewarrior-legacy/codewarrior-development-suite-special:CW-SUITE-SPECIAL|Codewarrior Development Studio for HCS12(X)]] development environment. |
| ===== Building and programming the Bootloader ===== | ===== Building and programming the Bootloader ===== | ||
| + | |||
| Before the bootloader can be used, it needs to be built and programmed into the HCS12DG256's internal flash memory. The steps in this section only need to be done once. | Before the bootloader can be used, it needs to be built and programmed into the HCS12DG256's internal flash memory. The steps in this section only need to be done once. | ||
| Line 28: | Line 30: | ||
| ===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
| + | |||
| When using Freescale Codewarrior, simply open the project from within Codewarrior and select //Project->Make// from the menu. The project file is located at: \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Prog**\ide\ | When using Freescale Codewarrior, simply open the project from within Codewarrior and select //Project->Make// from the menu. The project file is located at: \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Prog**\ide\ | ||
| The output file is | The output file is | ||
| + | |||
| * \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Prog**\bin\**demoprog_evbplus_dragon12p.abs.sx** | * \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Prog**\bin\**demoprog_evbplus_dragon12p.abs.sx** | ||
| ===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
| + | |||
| To download the demo program \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Prog**\bin\**demoprog_evbplus_dragon12p.abs.sx** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | To download the demo program \Target\Demo\HCS12_Evbplus_Dragon12p_CodeWarrior\**Prog**\bin\**demoprog_evbplus_dragon12p.abs.sx** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | ||
| - | * [[manual:uart_demo|Firmware updates using the UART communication interface]] | + | * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] |
| * [[manual:can_demo|Firmware updates using the CAN communication interface]] | * [[manual:can_demo|Firmware updates using the CAN communication interface]] | ||
| ===== Resolving Build Errors ===== | ===== Resolving Build Errors ===== | ||
| + | |||
| When building the demo binaries for the first time, build errors might occur caused by CodeWarrior projects not correctly dealing with relative directories and having source-files in a project that have the same name as source-files in the library path. These errors are quickly resolved by removing the file from the project and adding them again. | When building the demo binaries for the first time, build errors might occur caused by CodeWarrior projects not correctly dealing with relative directories and having source-files in a project that have the same name as source-files in the library path. These errors are quickly resolved by removing the file from the project and adding them again. | ||
manual/demos/evbplus_dragon12p_codewarrior.1432310757.txt.gz · Last modified: 2019/09/24 22:13 (external edit)
Page Tools
