This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
manual:demos:infineon_xmc1400_boot_kit_gcc [2017/04/24 14:59] voorburg [Building and programming the Bootloader] |
manual:demos:infineon_xmc1400_boot_kit_gcc [2019/09/24 22:12] 127.0.0.1 external edit |
||
---|---|---|---|
Line 10: | Line 10: | ||
{{:manual:demos:infineon_xmc1400_boot_kit.jpg?200 |}} | {{:manual:demos:infineon_xmc1400_boot_kit.jpg?200 |}} | ||
- | This demo is targeted towards the [[http://www.infineon.com/cms/en/product/evaluation-boards/KIT_XMC14_BOOT_001/productType.html?productType=5546d46250cc1fdf015144a2102e1191|Infineon XMC1400 Boot Kit]] board, with 200 kB internal Flash EEPROM and 16 kB internal RAM. | + | This demo is targeted towards the [[https://www.infineon.com/cms/en/product/evaluation-boards/kit_xmc14_boot_001/|Infineon XMC1400 Boot Kit]] board, with 200 kB internal Flash EEPROM and 16 kB internal RAM. |
To program the bootloader into the internal flash on the XMC1400 microcontroller, the on-board [[http://www.segger.com/development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. | To program the bootloader into the internal flash on the XMC1400 microcontroller, the on-board [[http://www.segger.com/development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. | ||
Line 43: | Line 43: | ||
* \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Boot**\Debug\**openblt_xmc1400.srec** | * \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Boot**\Debug\**openblt_xmc1400.srec** | ||
+ | Note that after closing the debug session in Eclipse, the on-board Segger J-Link interface halts the CPU. If you want to continue running the bootloader program, a reset of the microcontroller is needed. An easy method to achieve this is by disconnecting and then reconnecting the USB cable. | ||
===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
- | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (xmc1400.eww) is located at: \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable. | + | Set the project as the active project in Eclipse. This is achieved by right-clicking the **Prog** project in the project navigator called //C/C++ Projects//. From the context menu, select //Set Active Project//. Next, select //Project → Rebuild Active Project// from the menu to compile all the user program sources and link them together into the final executable. |
The output file is | The output file is | ||
- | * \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\bin\**demoprog_xmc1400.srec** | + | * \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Prog**\Debug\**demoprog_xmc1400.srec** |
===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
- | To download the demo program \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\bin\**demoprog_xmc1400.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | + | To download the demo program \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Prog**\Debug\**demoprog_xmc1400.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: |
* [[manual:uart_demo|Firmware updates using the UART communication interface]] | * [[manual:uart_demo|Firmware updates using the UART communication interface]] | ||
* [[manual:can_demo|Firmware updates using the CAN communication interface]] | * [[manual:can_demo|Firmware updates using the CAN communication interface]] | ||