User Tools

Site Tools


manual:demos:infineon_xmc1400_boot_kit_gcc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
manual:demos:infineon_xmc1400_boot_kit_gcc [2017/04/24 14:59]
voorburg [Building and programming the Bootloader]
manual:demos:infineon_xmc1400_boot_kit_gcc [2020/02/06 16:47]
voorburg
Line 3: Line 3:
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
  
-UART           ^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^+RS232          ​^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^
 | Yes            | Yes             | No           | No           | No          | | Yes            | Yes             | No           | No           | No          |
  
Line 10: Line 10:
 {{:​manual:​demos:​infineon_xmc1400_boot_kit.jpg?​200 |}} {{:​manual:​demos:​infineon_xmc1400_boot_kit.jpg?​200 |}}
  
-This demo is targeted towards the [[http://​www.infineon.com/​cms/​en/​product/​evaluation-boards/​KIT_XMC14_BOOT_001/productType.html?​productType=5546d46250cc1fdf015144a2102e1191|Infineon XMC1400 Boot Kit]] board, with 200 kB internal Flash EEPROM and 16 kB internal RAM.+This demo is targeted towards the [[https://​www.infineon.com/​cms/​en/​product/​evaluation-boards/​kit_xmc14_boot_001/|Infineon XMC1400 Boot Kit]] board, with 200 kB internal Flash EEPROM and 16 kB internal RAM.
  
 To program the bootloader into the internal flash on the XMC1400 microcontroller,​ the on-board [[http://​www.segger.com/​development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. ​ To program the bootloader into the internal flash on the XMC1400 microcontroller,​ the on-board [[http://​www.segger.com/​development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. ​
Line 43: Line 43:
   * \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Boot**\Debug\**openblt_xmc1400.srec**   * \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Boot**\Debug\**openblt_xmc1400.srec**
  
 +Note that after closing the debug session in Eclipse, the on-board Segger J-Link interface halts the CPU. If you want to continue running the bootloader program, a reset of the microcontroller is needed. An easy method to achieve this is by disconnecting and then reconnecting the USB cable.
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-When using IAR EWARM, simply open the workspace from within ​the Embedded WorkbenchThe workspace file (xmc1400.eww) ​is located at: \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\ide\Once opened, select //Project->Rebuild ​All// from the menu to compile all the demo program sources and link the together into the final executable.+Set the project as the active project in EclipseThis is achieved by right-clicking the **Prog** ​project in the project navigator called //C/C++ Projects//From the context menu, select //Set Active ​Project//. Next, select //Project → Rebuild ​Active Project// from the menu to compile all the user program sources and link them together into the final executable.
  
 The output file is The output file is
  
-  * \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\bin\**demoprog_xmc1400.srec**+  * \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Prog**\Debug\**demoprog_xmc1400.srec**
  
  
 ===== Firmware update procedure ===== ===== Firmware update procedure =====
  
-To download the demo program \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\bin\**demoprog_xmc1400.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:+To download the demo program \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Prog**\Debug\**demoprog_xmc1400.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:
  
-  * [[manual:uart_demo|Firmware updates using the UART communication interface]]+  * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]]
   * [[manual:​can_demo|Firmware updates using the CAN communication interface]]   * [[manual:​can_demo|Firmware updates using the CAN communication interface]]
  
manual/demos/infineon_xmc1400_boot_kit_gcc.txt · Last modified: 2023/12/04 22:39 by voorburg