User Tools

Site Tools


manual:demos:infineon_xmc1400_boot_kit_gcc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:demos:infineon_xmc1400_boot_kit_gcc [2017/04/24 15:02]
voorburg [Building and programming the Bootloader]
manual:demos:infineon_xmc1400_boot_kit_gcc [2020/02/06 16:47]
voorburg
Line 3: Line 3:
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
  
-UART           ^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^+RS232          ​^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^
 | Yes            | Yes             | No           | No           | No          | | Yes            | Yes             | No           | No           | No          |
  
Line 10: Line 10:
 {{:​manual:​demos:​infineon_xmc1400_boot_kit.jpg?​200 |}} {{:​manual:​demos:​infineon_xmc1400_boot_kit.jpg?​200 |}}
  
-This demo is targeted towards the [[http://​www.infineon.com/​cms/​en/​product/​evaluation-boards/​KIT_XMC14_BOOT_001/productType.html?​productType=5546d46250cc1fdf015144a2102e1191|Infineon XMC1400 Boot Kit]] board, with 200 kB internal Flash EEPROM and 16 kB internal RAM.+This demo is targeted towards the [[https://​www.infineon.com/​cms/​en/​product/​evaluation-boards/​kit_xmc14_boot_001/|Infineon XMC1400 Boot Kit]] board, with 200 kB internal Flash EEPROM and 16 kB internal RAM.
  
 To program the bootloader into the internal flash on the XMC1400 microcontroller,​ the on-board [[http://​www.segger.com/​development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. ​ To program the bootloader into the internal flash on the XMC1400 microcontroller,​ the on-board [[http://​www.segger.com/​development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. ​
Line 46: Line 46:
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-When using IAR EWARM, simply open the workspace from within ​the Embedded WorkbenchThe workspace file (xmc1400.eww) ​is located at: \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\ide\Once opened, select //Project->Rebuild ​All// from the menu to compile all the demo program sources and link the together into the final executable.+Set the project as the active project in EclipseThis is achieved by right-clicking the **Prog** ​project in the project navigator called //C/C++ Projects//From the context menu, select //Set Active ​Project//. Next, select //Project → Rebuild ​Active Project// from the menu to compile all the user program sources and link them together into the final executable.
  
 The output file is The output file is
  
-  * \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\bin\**demoprog_xmc1400.srec**+  * \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Prog**\Debug\**demoprog_xmc1400.srec**
  
  
 ===== Firmware update procedure ===== ===== Firmware update procedure =====
  
-To download the demo program \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\bin\**demoprog_xmc1400.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:+To download the demo program \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Prog**\Debug\**demoprog_xmc1400.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:
  
-  * [[manual:uart_demo|Firmware updates using the UART communication interface]]+  * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]]
   * [[manual:​can_demo|Firmware updates using the CAN communication interface]]   * [[manual:​can_demo|Firmware updates using the CAN communication interface]]
  
manual/demos/infineon_xmc1400_boot_kit_gcc.txt · Last modified: 2020/02/06 16:47 by voorburg