User Tools

Site Tools


manual:demos:infineon_xmc1400_boot_kit_gcc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:demos:infineon_xmc1400_boot_kit_gcc [2017/04/24 15:04]
voorburg [Building the Demo Program]
manual:demos:infineon_xmc1400_boot_kit_gcc [2023/12/04 22:39] (current)
voorburg [Supported firmware update interfaces]
Line 3: Line 3:
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
  
-UART           ^ CAN             ​^ USB          ^ TCP/​IP ​      ​^ SD-card ​     ^ +RS232         ^ CAN            ^ USB         ​^ TCP/​IP ​     ^ SD-card ​     ​^ Modbus RTU   
-| Yes            | Yes             ​| No           ​| No           | No          |+| Yes           ​| Yes            | No          | No          ​| No           | No           ​|
  
 ===== Development Environment ===== ===== Development Environment =====
Line 10: Line 10:
 {{:​manual:​demos:​infineon_xmc1400_boot_kit.jpg?​200 |}} {{:​manual:​demos:​infineon_xmc1400_boot_kit.jpg?​200 |}}
  
-This demo is targeted towards the [[http://​www.infineon.com/​cms/​en/​product/​evaluation-boards/​KIT_XMC14_BOOT_001/productType.html?​productType=5546d46250cc1fdf015144a2102e1191|Infineon XMC1400 Boot Kit]] board, with 200 kB internal Flash EEPROM and 16 kB internal RAM.+This demo is targeted towards the [[https://​www.infineon.com/​cms/​en/​product/​evaluation-boards/​kit_xmc14_boot_001/|Infineon XMC1400 Boot Kit]] board, with 200 kB internal Flash EEPROM and 16 kB internal RAM.
  
 To program the bootloader into the internal flash on the XMC1400 microcontroller,​ the on-board [[http://​www.segger.com/​development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. ​ To program the bootloader into the internal flash on the XMC1400 microcontroller,​ the on-board [[http://​www.segger.com/​development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. ​
Line 57: Line 57:
 To download the demo program \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Prog**\Debug\**demoprog_xmc1400.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: To download the demo program \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_GCC\**Prog**\Debug\**demoprog_xmc1400.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:
  
-  * [[manual:uart_demo|Firmware updates using the UART communication interface]]+  * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]]
   * [[manual:​can_demo|Firmware updates using the CAN communication interface]]   * [[manual:​can_demo|Firmware updates using the CAN communication interface]]
  
manual/demos/infineon_xmc1400_boot_kit_gcc.1493039085.txt.gz · Last modified: 2019/09/24 22:14 (external edit)