User Tools

Site Tools


manual:demos:infineon_xmc1400_boot_kit_iar

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:demos:infineon_xmc1400_boot_kit_iar [2016/12/21 11:36]
voorburg [Building and programming the Bootloader]
manual:demos:infineon_xmc1400_boot_kit_iar [2023/12/04 22:39] (current)
voorburg [Supported firmware update interfaces]
Line 3: Line 3:
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
  
-UART           ^ CAN             ​^ USB          ^ TCP/​IP ​      ​^ SD-card ​     ^ +RS232         ^ CAN            ^ USB         ​^ TCP/​IP ​     ^ SD-card ​     ​^ Modbus RTU   
-| Yes            | Yes             ​| No           ​| No           | No          |+| Yes           ​| Yes            | No          | No          ​| No           | No           ​|
  
 ===== Development Environment ===== ===== Development Environment =====
Line 10: Line 10:
 {{:​manual:​demos:​infineon_xmc1400_boot_kit.jpg?​200 |}} {{:​manual:​demos:​infineon_xmc1400_boot_kit.jpg?​200 |}}
  
-This demo is targeted towards the [[http://​www.infineon.com/​cms/​en/​product/​evaluation-boards/​KIT_XMC14_BOOT_001/productType.html?​productType=5546d46250cc1fdf015144a2102e1191|Infineon XMC1400 Boot Kit]] board, with 200 kB internal Flash EEPROM and 16 kB internal RAM.+This demo is targeted towards the [[https://​www.infineon.com/​cms/​en/​product/​evaluation-boards/​kit_xmc14_boot_001/|Infineon XMC1400 Boot Kit]] board, with 200 kB internal Flash EEPROM and 16 kB internal RAM.
  
 To program the bootloader into the internal flash on the XMC1400 microcontroller,​ the on-board [[http://​www.segger.com/​development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. ​ To program the bootloader into the internal flash on the XMC1400 microcontroller,​ the on-board [[http://​www.segger.com/​development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. ​
Line 32: Line 32:
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f0.eww) is located at: \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Prog**\ide\. Once opened, select //​Project->​Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable.+When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (xmc1400.eww) is located at: \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\ide\. Once opened, select //​Project->​Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable.
  
 The output file is The output file is
  
-  * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Prog**\bin\**demoprog_stm32f051.srec**+  * \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\bin\**demoprog_xmc1400.srec**
  
  
 ===== Firmware update procedure ===== ===== Firmware update procedure =====
  
-To download the demo program \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Prog**\bin\**demoprog_stm32f051.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:+To download the demo program \Target\Demo\ARMCM0_XMC1_XMC1400_Boot_Kit_IAR\**Prog**\bin\**demoprog_xmc1400.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:
  
-  * [[manual:uart_demo|Firmware updates using the UART communication interface]]+  * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] 
 +  * [[manual:​can_demo|Firmware updates using the CAN communication interface]]
  
manual/demos/infineon_xmc1400_boot_kit_iar.1482316577.txt.gz · Last modified: 2019/09/24 22:13 (external edit)