This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
manual:demos:infineon_xmc4700_relax_kit_iar [2018/08/20 13:52] voorburg [Firmware update procedure] |
manual:demos:infineon_xmc4700_relax_kit_iar [2023/12/04 22:40] voorburg [Supported firmware update interfaces] |
||
---|---|---|---|
Line 3: | Line 3: | ||
===== Supported firmware update interfaces ===== | ===== Supported firmware update interfaces ===== | ||
- | ^ UART ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ |
- | | Yes | Yes | No | Yes | No | | + | | Yes | Yes | Yes | Yes | Yes | No | |
===== Development Environment ===== | ===== Development Environment ===== | ||
Line 10: | Line 10: | ||
{{:manual:demos:infineon_xmc700_relax_kit.jpg?100 |}} | {{:manual:demos:infineon_xmc700_relax_kit.jpg?100 |}} | ||
- | This demo is targeted towards the [[http://www.infineon.com/cms/en/product/evaluation-boards/KIT_XMC47_RELAX_V1/productType.html?productType=5546d46250cc1fdf0150f6bdcddb6ec7|Infineon XMC4700 Relax Kit]] board, with 2048 kB internal Flash EEPROM and 352 kB internal RAM. | + | This demo is targeted towards the [[https://www.infineon.com/cms/en/product/evaluation-boards/kit_xmc47_relax_v1/|Infineon XMC4700 Relax Kit]] board, with 2048 kB internal Flash EEPROM and 352 kB internal RAM. |
To program the bootloader into the internal flash on the XMC4700 microcontroller, the on-board [[http://www.segger.com/development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. | To program the bootloader into the internal flash on the XMC4700 microcontroller, the on-board [[http://www.segger.com/development-tools.html|Segger J-Link]] JTAG interface was used. However, this is not required if you have another means of programming the internal flash. | ||
Line 43: | Line 43: | ||
To download the demo program \Target\Demo\ARMCM4_XMC4_XMC4700_Relax_Kit_IAR\**Prog**\bin\**demoprog_xmc4700.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | To download the demo program \Target\Demo\ARMCM4_XMC4_XMC4700_Relax_Kit_IAR\**Prog**\bin\**demoprog_xmc4700.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | ||
- | * [[manual:uart_demo|Firmware updates using the UART communication interface]] | + | * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] |
* [[manual:can_demo|Firmware updates using the CAN communication interface]] | * [[manual:can_demo|Firmware updates using the CAN communication interface]] | ||
+ | * [[manual:usb_demo|Firmware updates using the USB communication interface]] | ||
* [[manual:net_demo|Firmware updates using the TCP/IP communication interface]] | * [[manual:net_demo|Firmware updates using the TCP/IP communication interface]] | ||
+ | * [[manual:sdcard_demo|Firmware updates from SD-card]] | ||