This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
manual:demos:nucleo_f091rc_gcc [2017/07/19 15:13] voorburg |
manual:demos:nucleo_f091rc_gcc [2023/12/04 22:17] (current) voorburg [Supported firmware update interfaces] |
||
---|---|---|---|
Line 3: | Line 3: | ||
===== Supported firmware update interfaces ===== | ===== Supported firmware update interfaces ===== | ||
- | ^ UART ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ |
- | | Yes | Yes | No | No | No | | + | | Yes | Yes | No | No | No | No | |
===== Development Environment ===== | ===== Development Environment ===== | ||
Line 28: | Line 28: | ||
Before the bootloader can be used, it needs to be built and programmed into the STM32F091's internal flash memory. The steps in this section only need to be done once. | Before the bootloader can be used, it needs to be built and programmed into the STM32F091's internal flash memory. The steps in this section only need to be done once. | ||
- | To build the bootloader, open a command prompt in directory **\Target\Demo\RMCM0_STM32F0_Nucleo_F091RC_GCC\Boot\** and run the command: | + | To build the bootloader, open a command prompt in directory **\Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_GCC\Boot\** and run the command: |
<code> | <code> | ||
Line 56: | Line 56: | ||
===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
- | When using EmBitz, simply open the project file by double-clicking the file: \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_GCC\**Prog**\ide\**stm32f091.ebp** from the Windows Explorer. To build the demo program, select //Build -> Rebuild all target files// from the program's menu. | + | To build the user program, open a command prompt in directory **\Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_GCC\Prog\** and run the command: |
+ | |||
+ | <code> | ||
+ | make clean all | ||
+ | </code> | ||
+ | |||
+ | The expected output is: | ||
+ | |||
+ | <code> | ||
+ | +++ Cleaning build environment | ||
+ | +++ Clean complete | ||
+ | +++ Assembling [startup_stm32f0xx.S] | ||
+ | +++ Compiling [boot.c] | ||
+ | +++ Compiling [main.c] | ||
+ | ... | ||
+ | +++ Linking [demoprog_stm32f091.elf] | ||
+ | ... | ||
+ | +++ Build complete [demoprog_stm32f091.srec] | ||
+ | |||
+ | </code> | ||
The output file is | The output file is | ||
* \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_GCC\**Prog**\bin\**demoprog_stm32f091.srec** | * \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_GCC\**Prog**\bin\**demoprog_stm32f091.srec** | ||
- | |||
===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
Line 67: | Line 85: | ||
To download the demo program \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_GCC\**Prog**\bin\**demoprog_stm32f091.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | To download the demo program \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_GCC\**Prog**\bin\**demoprog_stm32f091.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | ||
- | * [[manual:uart_demo|Firmware updates using the UART communication interface]] | + | * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] |
* [[manual:can_demo|Firmware updates using the CAN communication interface]] | * [[manual:can_demo|Firmware updates using the CAN communication interface]] | ||