manual:demos:nucleo_f103rb_gcc
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Next revision Both sides next revision | ||
|
manual:demos:nucleo_f103rb_gcc [2017/05/23 19:06] voorburg created |
manual:demos:nucleo_f103rb_gcc [2017/05/23 19:16] voorburg [Building and programming the Bootloader] |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| ===== Development Environment ===== | ===== Development Environment ===== | ||
| - | {{:manual:demos:olimex_stm32p103.gif?200 |}} | + | {{:manual:demos:stm32_nucleo_f103rb.png? |}} |
| - | This demo is targeted towards the [[http://olimex.com/dev/stm32-p103.html|Olimex STM32P103]] board, with 128 kB internal Flash EEPROM and 20 kB internal RAM. | + | This demo is targeted towards the [[http://www.st.com/en/evaluation-tools/nucleo-f103rb.html|Nucleo-F103RB]] board, with 128 kB internal Flash EEPROM and 20 kB internal RAM. |
| - | To program the bootloader into the internal flash on the STM32F103 microcontroller, the [[http://www.olimex.com/dev/arm-usb-tiny-h.html|Olimex ARM-USB-TINY-H]] JTAG interface was used in combination with [[http://openocd.sourceforge.net/|OpenOCD 0.4.0]]. However, this is not required if you have another means of programming the internal flash. | + | To program the bootloader into the internal flash on the on-board ST-Link debugger interface was used. Firmware updates via the serial communication port are preconfigured to use the virtual COM-port offered by the ST-Link. This means that no additional hardware is needed, besides a standard micro-USB cable. |
| The demo programs are pre-configured for building with the {{:manual:arm-2013.11-24-arm-none-eabi.zip?linkonly|Codesourcery G++ Lite}} (Target OS EABI) toolchain. Alternatively, you can use the [[manual:demos:gcc_arm_embedded|GCC ARM Embedded]] toolchain. | The demo programs are pre-configured for building with the {{:manual:arm-2013.11-24-arm-none-eabi.zip?linkonly|Codesourcery G++ Lite}} (Target OS EABI) toolchain. Alternatively, you can use the [[manual:demos:gcc_arm_embedded|GCC ARM Embedded]] toolchain. | ||
| Line 20: | Line 20: | ||
| Before the bootloader can be used, it needs to be built and programmed into the STM32F103's internal flash memory. The steps in this section only need to be done once. | Before the bootloader can be used, it needs to be built and programmed into the STM32F103's internal flash memory. The steps in this section only need to be done once. | ||
| - | Batch files are added to aid in building the software program. First clean the bootloader program by double-clicking the file "\Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Boot**\cmd\**clean.bat**". Next, build the bootloader program by double-clicking the file "\Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Boot**\cmd\**build.bat**". The output should look like: | + | Batch files are added to aid in building the software program. First clean the bootloader program by double-clicking the file "\Target\Demo\ARMCM3_STM32F1_Nucleo_F103RB_GCC\**Boot**\cmd\**clean.bat**". Next, build the bootloader program by double-clicking the file "\Target\Demo\ARMCM3_STM32F1_Nucleo_F103RB_GCC\**Boot**\cmd\**build.bat**". The output should look like: |
| <code> | <code> | ||
| Line 27: | Line 27: | ||
| +++ Compiling [boot.o] | +++ Compiling [boot.o] | ||
| ... | ... | ||
| - | +++ Linking [openblt_olimex_stm32p103.elf] | + | +++ Linking [openblt_nucleo_stm32f103rb.elf] |
| ... | ... | ||
| - | +++ Build complete [openblt_olimex_stm32p103.srec] | + | +++ Build complete [openblt_nucleo_stm32f103rb.srec] |
| </code> | </code> | ||
| The bootloader program is now ready to be programmed into the internal flash memory of the STM32F103. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports: | The bootloader program is now ready to be programmed into the internal flash memory of the STM32F103. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports: | ||
| - | * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Boot**\bin\**openblt_olimex_stm32p103.elf** | + | * \Target\Demo\ARMCM3_STM32F1_Nucleo_F103RB_GCC\**Boot**\bin\**openblt_nucleo_stm32f103rb.elf** |
| - | * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Boot**\bin\**openblt_olimex_stm32p103.srec** | + | * \Target\Demo\ARMCM3_STM32F1_Nucleo_F103RB_GCC\**Boot**\bin\**openblt_nucleo_stm32f103rb.srec** |
| ===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
manual/demos/nucleo_f103rb_gcc.txt · Last modified: 2023/12/04 22:18 by voorburg
Page Tools
