User Tools

Site Tools


manual:demos:nucleo_f103rb_gcc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
manual:demos:nucleo_f103rb_gcc [2017/05/23 20:27]
voorburg [Development Environment]
manual:demos:nucleo_f103rb_gcc [2019/09/24 22:12]
127.0.0.1 external edit
Line 14: Line 14:
 To program the bootloader into the internal flash, the on-board ST-Link debugger interface was used. Firmware updates via the serial communication port are preconfigured to use the virtual COM-port offered by the ST-Link. This means that no additional hardware is needed, besides a standard micro-USB cable. To program the bootloader into the internal flash, the on-board ST-Link debugger interface was used. Firmware updates via the serial communication port are preconfigured to use the virtual COM-port offered by the ST-Link. This means that no additional hardware is needed, besides a standard micro-USB cable.
  
-The demo programs are pre-configured for building with the {{:​manual:​arm-2013.11-24-arm-none-eabi.zip?linkonly|Codesourcery G++ Lite}} (Target OS EABItoolchainAlternatively,​ you can use the [[manual:​demos:gcc_arm_embedded|GCC ARM Embedded]] toolchain.+To build the demo programs you can use the [[https://​developer.arm.com/​open-source/​gnu-toolchain/​gnu-rm|GNU ARM Embedded]] toolchain. 
 + 
 +===== Toolchain configuration ===== 
 + 
 +The demo programs are configured for building with a Makefile. Before attempting to perform a build, update ​the location of the toolchain binaries (i.e. //arm-none-eabi-gcc//) in the MakefileIt is set in variable **TOOL_PATH**. If the toolchain binaries are available on the path, then the **TOOL_PATH** variable can be left empty. 
 + 
 +{{:​manual:​demos:​makefile_toolpath.png?nolink&|}} 
 + 
 + 
 +It is assumed that tools such as GNU //make// and //rm// are installed and available on the path. For (UbuntuLinux users this can be achieved by running command: //sudo apt-get install build-essential//​Windows users can install ​the [[https://​gnu-mcu-eclipse.github.io/​windows-build-tools/​|GNU MCU Eclipse Windows Build Tools]].
  
 ===== Building and programming the Bootloader ===== ===== Building and programming the Bootloader =====
Line 20: Line 29:
 Before the bootloader can be used, it needs to be built and programmed into the STM32F103'​s internal flash memory. The steps in this section only need to be done once. Before the bootloader can be used, it needs to be built and programmed into the STM32F103'​s internal flash memory. The steps in this section only need to be done once.
  
-Batch files are added to aid in building the software program. First clean the bootloader ​program by double-clicking the file "​\Target\Demo\ARMCM3_STM32F1_Nucleo_F103RB_GCC\**Boot**\cmd\**clean.bat**"​. Next, build the bootloader program by double-clicking the file "\Target\Demo\ARMCM3_STM32F1_Nucleo_F103RB_GCC\**Boot**\cmd\**build.bat**"​. ​The output ​should look like:+To build the bootloader, open a command prompt in directory ​**\Target\Demo\ARMCM3_STM32F1_Nucleo_F103RB_GCC\Boot\** ​and run the command: 
 + 
 +<​code>​ 
 +make clean all 
 +</​code>​ 
 +  
 +The expected ​output ​is:
  
 <​code>​ <​code>​
Line 39: Line 54:
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-Batch files are added to aid in building ​the demo program. First clean the demo program by double-clicking the file "​\Target\Demo\ARMCM3_STM32F1_Nucleo_F103RB_GCC\**Prog**\cmd\**clean.bat**"​. Next, build the demo program by double-clicking the file "\Target\Demo\ARMCM3_STM32F1_Nucleo_F103RB_GCC\**Prog**\cmd\**build.bat**"​. ​The output ​should look like:+To build the user program, open a command prompt in directory ​**\Target\Demo\ARMCM3_STM32F1_Nucleo_F103RB_GCC\Prog\** ​and run the command: 
 + 
 +<​code>​ 
 +make clean all 
 +</​code>​ 
 +  
 +The expected ​output ​is:
  
 <​code>​ <​code>​
manual/demos/nucleo_f103rb_gcc.txt · Last modified: 2020/02/06 16:21 by voorburg