This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
manual:demos:nucleo_f303k8_gcc [2016/11/14 17:32] voorburg [Development Environment] |
manual:demos:nucleo_f303k8_gcc [2016/11/14 17:35] voorburg [Firmware update procedure] |
||
---|---|---|---|
Line 19: | Line 19: | ||
===== Building and programming the Bootloader ===== | ===== Building and programming the Bootloader ===== | ||
- | Before the bootloader can be used, it needs to be built and programmed into the STM32F207's internal flash memory. The steps in this section only need to be done once. | + | Before the bootloader can be used, it needs to be built and programmed into the STM32F303's internal flash memory. The steps in this section only need to be done once. |
- | When using EmBitz, simply open the project file by double-clicking the file: \Target\Demo\ARMCM3_STM32F2_Olimex_STM32P207_GCC\**Boot**\ide\**stm32f207.ebp** from the Windows Explorer. To build the bootloader, select //Build -> Rebuild all target files// from the program menu. | + | When using EmBitz, simply open the project file by double-clicking the file: \Target\Demo\ARMCM4_STM32F3_Nucleo_F303K8_GCC\**Boot**\ide\**stm32f303.ebp** from the Windows Explorer. To build the bootloader, select //Build -> Rebuild all target files// from the program menu. |
- | The bootloader program is now ready to be programmed into the internal flash memory of the STM32F207. Make sure the Segger J-Link debugger interface it connected to the JTAG connector on the Olimex STM32-P207 board and the other side to your PC via a USB cable. Next, select //Debug -> Start Debug Session (F8)// from EmBitz's program menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Run (F5)// from the program's menu. | + | The bootloader program is now ready to be programmed into the internal flash memory of the STM32F303. Make sure the board is connected to your PC via a micro-USB cable. Next, select //Debug -> Start Debug Session (F8)// from EmBitz's program menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Run (F5)// from the program's menu. |
Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | ||
- | * \Target\Demo\ARMCM3_STM32F2_Olimex_STM32P207_GCC\**Boot**\bin\**openblt_stm32f207.elf** | + | * \Target\Demo\ARMCM4_STM32F3_Nucleo_F303K8_GCC\**Boot**\bin\**openblt_stm32f303.elf** |
- | * \Target\Demo\ARMCM3_STM32F2_Olimex_STM32P207_GCC\**Boot**\bin\**openblt_stm32f207.srec** | + | * \Target\Demo\ARMCM4_STM32F3_Nucleo_F303K8_GCC\**Boot**\bin\**openblt_stm32f303.srec** |
===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
- | When using EmBitz, simply open the project file by double-clicking the file: \Target\Demo\ARMCM3_STM32F2_Olimex_STM32P207_GCC\**Prog**\ide\**stm32f207.ebp** from the Windows Explorer. To build the demo program, select //Build -> Rebuild all target files// from the program's menu. | + | When using EmBitz, simply open the project file by double-clicking the file: \Target\Demo\ARMCM4_STM32F3_Nucleo_F303K8_GCC\**Prog**\ide\**stm32f303.ebp** from the Windows Explorer. To build the demo program, select //Build -> Rebuild all target files// from the program's menu. |
The output file is | The output file is | ||
- | * \Target\Demo\ARMCM3_STM32F2_Olimex_STM32P207_GCC\**Prog**\bin\**demoprog_stm32f207.srec** | + | * \Target\Demo\ARMCM4_STM32F3_Nucleo_F303K8_GCC\**Prog**\bin\**demoprog_stm32f303.srec** |
===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
- | To download the demo program \Target\Demo\ARMCM3_STM32F2_Olimex_STM32P207_GCC\**Prog**\bin\**demoprog_stm32f207.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | + | To download the demo program \Target\Demo\ARMCM4_STM32F3_Nucleo_F303K8_GCC\**Prog**\bin\**demoprog_stm32f303.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: |
* [[manual:uart_demo|Firmware updates using the UART communication interface]] | * [[manual:uart_demo|Firmware updates using the UART communication interface]] | ||
* [[manual:can_demo|Firmware updates using the CAN communication interface]] | * [[manual:can_demo|Firmware updates using the CAN communication interface]] | ||
- | * [[manual:sdcard_demo|Firmware updates from SD-card]] | ||