User Tools

Site Tools


manual:demos:nucleo_f746zg_cubeide

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:demos:nucleo_f746zg_cubeide [2020/09/22 17:08]
voorburg
manual:demos:nucleo_f746zg_cubeide [2023/12/04 22:30] (current)
voorburg [Supported firmware update interfaces]
Line 1: Line 1:
-====== ARM-CM7 STM32 Nucleo-F746ZG ​ ======+====== ARM-CM7 STM32 Nucleo-F746ZG ​STM32CubeIDE ​======
  
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
  
-^ RS232          ^ CAN             ​^ USB          ^ TCP/​IP ​      ​^ SD-card ​     ^ +^ RS232         ​^ CAN            ^ USB         ​^ TCP/​IP ​     ^ SD-card ​     ​^ Modbus RTU   
-| Yes            | Yes             ​| Yes          | No           | No           |+| Yes           ​| Yes            | Yes         | No          | No           | No           |
  
 ===== Development Environment ===== ===== Development Environment =====
Line 34: Line 34:
 Before the bootloader can be used, it needs to be built and programmed into the STM32F746ZG'​s internal flash memory. The steps in this section only need to be done once. Before the bootloader can be used, it needs to be built and programmed into the STM32F746ZG'​s internal flash memory. The steps in this section only need to be done once.
  
-- Set the project as the active project in Eclipse. This is achieved by clicking the **Boot** project in the //Project Explorer// to select it. +  ​- Set the project as the active project in Eclipse. This is achieved by clicking the **Boot** project in the //Project Explorer// to select it. 
-- Delete the file \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_CubeIDE\**Boot**\Debug\**openblt_stm32f746.elf**. +  - Next, right-click the **Boot** project in the //Project Explorer// and select //Refresh// from the popup menu. 
-- Next, right-click the **Boot** project in the //Project Explorer// and select //Refresh// from the popup menu. +  - Finally, right-click the **Boot** project in the //Project Explorer// and select //Build Project// from the popup menu to compile all the bootloader sources and link them together into the final executable.
-- Finally, right-click the **Boot** project in the //Project Explorer// and select //Build Project// from the popup menu to compile all the bootloader sources and link them together into the final executable.+
  
 The bootloader program is now ready to be programmed into the internal flash memory of the STM32F746ZG microcontroller. Make sure the Nucleo-F746ZG board is connected to your PC via a USB cable. Next, select //Run -> Debug// from the menu to flash the bootloader program. This will launch the Debug perspective in Eclipse. Once done, you can start the bootloader program by selecting //Run -> Resume// from the menu. The bootloader program is now ready to be programmed into the internal flash memory of the STM32F746ZG microcontroller. Make sure the Nucleo-F746ZG board is connected to your PC via a USB cable. Next, select //Run -> Debug// from the menu to flash the bootloader program. This will launch the Debug perspective in Eclipse. Once done, you can start the bootloader program by selecting //Run -> Resume// from the menu.
Line 48: Line 47:
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-Set the project as the active project in Eclipse. This is achieved by clicking the **Prog** project in the //Project Explorer// to select it. Right-click the **Prog** project in the //Project Explorer// and select //Clean Project// from the popup menu. Next, right-click the **Prog** project in the //Project Explorer// and select //Refresh// from the popup menu. Finally, right-click the **Prog** project in the //Project Explorer// and select //Build Project// from the popup menu to compile all the user program sources and link them together into the final executable. +  - Set the project as the active project in Eclipse. This is achieved by clicking the **Prog** project in the //Project Explorer// to select it. 
 +  ​- Next, right-click the **Prog** project in the //Project Explorer// and select //Refresh// from the popup menu. 
 +  - Finally, right-click the **Prog** project in the //Project Explorer// and select //Build Project// from the popup menu to compile all the user program sources and link them together into the final executable. 
 + 
 The output file is The output file is
  
manual/demos/nucleo_f746zg_cubeide.1600787328.txt.gz · Last modified: 2020/09/22 17:08 by voorburg