User Tools

Site Tools


manual:demos:nucleo_f746zg_gcc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
manual:demos:nucleo_f746zg_gcc [2018/12/10 12:58]
voorburg [Building and programming the Bootloader]
manual:demos:nucleo_f746zg_gcc [2020/02/06 16:33]
voorburg
Line 3: Line 3:
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
  
-UART           ^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^ +RS232          ​^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^ 
-| Yes            | Yes             ​| ​No           | No           | No           |+| Yes            | Yes             ​| ​Yes          ​| No           | No           |
  
 ===== Development Environment ===== ===== Development Environment =====
Line 55: Line 55:
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-To build the user program, open a command prompt in directory **\Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_GCC\Prog\** and run the command:+To build the user program, open a command prompt in directory **\Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_GCC\Prog\** and run the command:
  
 <​code>​ <​code>​
Line 64: Line 64:
  
 <​code>​ <​code>​
-+++ Cleaning build environment ​                                                                                        ​ ++++ Cleaning build environment 
-+++ Clean complete ​                                                                                                    ​ ++++ Clean complete 
-+++ Assembling [startup_stm32l476xx.s]                                                                                   ​ ++++ Assembling [startup_stm32f746xx.s] 
-+++ Compiling [boot.c]                                                                                                 ​ ++++ Compiling [timer.c] 
-+++ Compiling [main.c] ​                                                                                                ​++++ Compiling [main.c]
 ... ...
-+++ Linking [demoprog_stm32l476.elf]++++ Linking [demoprog_stm32f746.elf]
 ... ...
-+++ Build complete [demoprog_stm32l476.srec]++++ Build complete [demoprog_stm32f746.srec]
 </​code>​ </​code>​
  
 The output file is: The output file is:
  
-  * \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_GCC\**Prog**\bin\**demoprog_stm32l476.srec**+  * \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_GCC\**Prog**\bin\**demoprog_stm32f746.srec**
  
 ===== Firmware update procedure ===== ===== Firmware update procedure =====
  
-To download the demo program \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_GCC\**Prog**\bin\**demoprog_stm32l476.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:+To download the demo program \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_GCC\**Prog**\bin\**demoprog_stm32f746.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:
  
-  * [[manual:uart_demo|Firmware updates using the UART communication interface]]+  * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]]
   * [[manual:​can_demo|Firmware updates using the CAN communication interface]]   * [[manual:​can_demo|Firmware updates using the CAN communication interface]]
 +  * [[manual:​usb_demo|Firmware updates using the USB communication interface]]
  
manual/demos/nucleo_f746zg_gcc.txt · Last modified: 2023/12/04 22:29 by voorburg