User Tools

Site Tools


manual:demos:nucleo_f746zg_gcc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:demos:nucleo_f746zg_gcc [2018/12/10 12:58]
voorburg [Building and programming the Bootloader]
manual:demos:nucleo_f746zg_gcc [2020/02/06 16:33] (current)
voorburg
Line 3: Line 3:
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
  
-UART           ^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^ +RS232          ​^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^ 
-| Yes            | Yes             ​| ​No           | No           | No           |+| Yes            | Yes             ​| ​Yes          ​| No           | No           |
  
 ===== Development Environment ===== ===== Development Environment =====
Line 55: Line 55:
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-To build the user program, open a command prompt in directory **\Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_GCC\Prog\** and run the command:+To build the user program, open a command prompt in directory **\Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_GCC\Prog\** and run the command:
  
 <​code>​ <​code>​
Line 64: Line 64:
  
 <​code>​ <​code>​
-+++ Cleaning build environment ​                                                                                        ​ ++++ Cleaning build environment 
-+++ Clean complete ​                                                                                                    ​ ++++ Clean complete 
-+++ Assembling [startup_stm32l476xx.s]                                                                                   ​ ++++ Assembling [startup_stm32f746xx.s] 
-+++ Compiling [boot.c]                                                                                                 ​ ++++ Compiling [timer.c] 
-+++ Compiling [main.c] ​                                                                                                ​++++ Compiling [main.c]
 ... ...
-+++ Linking [demoprog_stm32l476.elf]++++ Linking [demoprog_stm32f746.elf]
 ... ...
-+++ Build complete [demoprog_stm32l476.srec]++++ Build complete [demoprog_stm32f746.srec]
 </​code>​ </​code>​
  
 The output file is: The output file is:
  
-  * \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_GCC\**Prog**\bin\**demoprog_stm32l476.srec**+  * \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_GCC\**Prog**\bin\**demoprog_stm32f746.srec**
  
 ===== Firmware update procedure ===== ===== Firmware update procedure =====
  
-To download the demo program \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_GCC\**Prog**\bin\**demoprog_stm32l476.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:+To download the demo program \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_GCC\**Prog**\bin\**demoprog_stm32f746.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:
  
-  * [[manual:uart_demo|Firmware updates using the UART communication interface]]+  * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]]
   * [[manual:​can_demo|Firmware updates using the CAN communication interface]]   * [[manual:​can_demo|Firmware updates using the CAN communication interface]]
 +  * [[manual:​usb_demo|Firmware updates using the USB communication interface]]
  
manual/demos/nucleo_f746zg_gcc.1544443086.txt.gz · Last modified: 2019/09/24 22:13 (external edit)