This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
manual:demos:nucleo_f746zg_iar [2018/12/17 10:36] voorburg [Development Environment] |
manual:demos:nucleo_f746zg_iar [2023/12/04 22:29] (current) voorburg [Supported firmware update interfaces] |
||
---|---|---|---|
Line 3: | Line 3: | ||
===== Supported firmware update interfaces ===== | ===== Supported firmware update interfaces ===== | ||
- | ^ UART ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ |
- | | Yes | Yes | No | No | No | | + | | Yes | Yes | Yes | No | No | No | |
===== Development Environment ===== | ===== Development Environment ===== | ||
Line 18: | Line 18: | ||
===== Building and programming the Bootloader ===== | ===== Building and programming the Bootloader ===== | ||
- | Before the bootloader can be used, it needs to be built and programmed into the STM32L476's internal flash memory. The steps in this section only need to be done once. | + | Before the bootloader can be used, it needs to be built and programmed into the STM32F746's internal flash memory. The steps in this section only need to be done once. |
- | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32l476.eww) is located at: \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_IAR\**Boot**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the bootloader sources and link them together into the final executable. | + | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f746.eww) is located at: \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_IAR\**Boot**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the bootloader sources and link them together into the final executable. |
- | The bootloader program is now ready to be programmed into the internal flash memory of the STM32L476. Select //Project -> Download and Debug (Ctrl+D)// from the menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Go (F5)// from the menu. | + | The bootloader program is now ready to be programmed into the internal flash memory of the STM32F746. Select //Project -> Download and Debug (Ctrl+D)// from the menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Go (F5)// from the menu. |
Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | ||
- | * \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_IAR\**Boot**\bin\**openblt_stm32l476.out** | + | * \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_IAR\**Boot**\bin\**openblt_stm32f746.out** |
- | * \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_IAR\**Boot**\bin\**openblt_stm32l476.srec** | + | * \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_IAR\**Boot**\bin\**openblt_stm32f746.srec** |
===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
- | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32l476.eww) is located at: \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_IAR\**Prog**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable. | + | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f746.eww) is located at: \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_IAR\**Prog**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable. |
The output file is | The output file is | ||
- | * \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_IAR\**Prog**\bin\**demoprog_stm32l476.srec** | + | * \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_IAR\**Prog**\bin\**demoprog_stm32f746.srec** |
===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
- | To download the demo program \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_IAR\**Prog**\bin\**demoprog_stm32l476.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | + | To download the demo program \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_IAR\**Prog**\bin\**demoprog_stm32f746.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: |
- | * [[manual:uart_demo|Firmware updates using the UART communication interface]] | + | * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] |
* [[manual:can_demo|Firmware updates using the CAN communication interface]] | * [[manual:can_demo|Firmware updates using the CAN communication interface]] | ||
+ | * [[manual:usb_demo|Firmware updates using the USB communication interface]] | ||