This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
manual:demos:nucleo_f746zg_truestudio [2018/12/10 12:15] voorburg [Workspace creation in TrueStudio] |
manual:demos:nucleo_f746zg_truestudio [2018/12/10 12:19] voorburg [Firmware update procedure] |
||
---|---|---|---|
Line 32: | Line 32: | ||
===== Building and programming the Bootloader ===== | ===== Building and programming the Bootloader ===== | ||
- | Before the bootloader can be used, it needs to be built and programmed into the STM32L476RG's internal flash memory. The steps in this section only need to be done once. | + | Before the bootloader can be used, it needs to be built and programmed into the STM32F746ZG's internal flash memory. The steps in this section only need to be done once. |
Set the project as the active project in Eclipse. This is achieved by clicking the **Boot** project in the //Project Explorer// to select it. Next, select //Project -> Rebuild Project// from the menu to compile all the bootloader sources and link them together into the final executable. | Set the project as the active project in Eclipse. This is achieved by clicking the **Boot** project in the //Project Explorer// to select it. Next, select //Project -> Rebuild Project// from the menu to compile all the bootloader sources and link them together into the final executable. | ||
- | The bootloader program is now ready to be programmed into the internal flash memory of the STM32L476RG microcontroller. Make sure the Nucleo-L476RG board is connected to your PC via a USB cable. Next, select //Run -> Debug// from the menu to flash the bootloader program. This will launch the Debug perspective in Eclipse. Once done, you can start the bootloader program by selecting //Run -> Resume// from the menu. | + | The bootloader program is now ready to be programmed into the internal flash memory of the STM32F746ZG microcontroller. Make sure the Nucleo-F746ZG board is connected to your PC via a USB cable. Next, select //Run -> Debug// from the menu to flash the bootloader program. This will launch the Debug perspective in Eclipse. Once done, you can start the bootloader program by selecting //Run -> Resume// from the menu. |
Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | ||
- | * \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_TrueStudio\**Boot**\Debug\**openblt_stm32l476.elf** | + | * \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_TrueStudio\**Boot**\Debug\**openblt_stm32f746.elf** |
- | * \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_TrueStudio\**Boot**\Debug\**openblt_stm32l476.srec** | + | * \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_TrueStudio\**Boot**\Debug\**openblt_stm32f746.srec** |
===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
Line 49: | Line 49: | ||
The output file is | The output file is | ||
- | * \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_TrueStudio\**Prog**\Debug\**demoprog_stm32l476.srec** | + | * \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_TrueStudio\**Prog**\Debug\**demoprog_stm32f746.srec** |
===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
- | To download the demo program \Target\Demo\ARMCM4_STM32L4_Nucleo_L476RG_TrueStudio\**Prog**\Debug\**demoprog_stm32l476.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | + | To download the demo program \Target\Demo\ARMCM7_STM32F7_Nucleo_F746ZG_TrueStudio\**Prog**\Debug\**demoprog_stm32f746.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: |
* [[manual:uart_demo|Firmware updates using the UART communication interface]] | * [[manual:uart_demo|Firmware updates using the UART communication interface]] |