User Tools

Site Tools


manual:demos:nucleo_g071rb_gcc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:demos:nucleo_g071rb_gcc [2019/08/13 15:27]
voorburg [Building and programming the Bootloader]
manual:demos:nucleo_g071rb_gcc [2020/02/06 16:36]
voorburg
Line 3: Line 3:
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
  
-UART           ^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^+RS232          ​^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^
 | Yes            | No              | No           | No           | No           | | Yes            | No              | No           | No           | No           |
  
Line 56: Line 56:
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-To build the user program, open a command prompt in directory **\Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_GCC\Prog\** and run the command:+To build the user program, open a command prompt in directory **\Target\Demo\ARMCM0_STM32G0_Nucleo_G071RB_GCC\Prog\** and run the command:
  
 <​code>​ <​code>​
Line 65: Line 65:
  
 <​code>​ <​code>​
-+++ Cleaning build environment ​                                                                                        ​ ++++ Cleaning build environment 
-+++ Clean complete ​                                                                                                    ​ ++++ Clean complete 
-+++ Assembling [startup_stm32f0xx.S                                                                                  ​ ++++ Assembling [startup_stm32g071xx.s
-+++ Compiling [boot.c]                                                                                                 ​ ++++ Compiling [main.c] 
-+++ Compiling [main.c]                                                                                                 ​++++ Compiling [boot.c]
 ... ...
-+++ Linking [demoprog_stm32f091.elf]++++ Linking [demoprog_stm32g071.elf]
 ... ...
-+++ Build complete [demoprog_stm32f091.srec] ++++ Build complete [demoprog_stm32g071.srec]
 </​code>​ </​code>​
  
 The output file is The output file is
  
-  * \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_GCC\**Prog**\bin\**demoprog_stm32f091.srec**+  * \Target\Demo\ARMCM0_STM32G0_Nucleo_G071RB_GCC\**Prog**\bin\**demoprog_stm32g071.srec**
  
 ===== Firmware update procedure ===== ===== Firmware update procedure =====
  
-To download the demo program \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_GCC\**Prog**\bin\**demoprog_stm32f091.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:+To download the demo program \Target\Demo\ARMCM0_STM32G0_Nucleo_G071RB_GCC\**Prog**\bin\**demoprog_stm32g071.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: 
 + 
 +  * [[manual:​rs232_demo|Firmware updates using the RS232 communication interface]]
  
-  * [[manual:​uart_demo|Firmware updates using the UART communication interface]] 
-  * [[manual:​can_demo|Firmware updates using the CAN communication interface]] 
  
  
manual/demos/nucleo_g071rb_gcc.txt · Last modified: 2020/02/06 16:36 by voorburg