This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
manual:demos:nucleo_g071rb_truestudio [2019/08/13 11:57] voorburg [Workspace creation in TrueStudio] |
manual:demos:nucleo_g071rb_truestudio [2020/02/06 16:37] (current) voorburg |
||
---|---|---|---|
Line 3: | Line 3: | ||
===== Supported firmware update interfaces ===== | ===== Supported firmware update interfaces ===== | ||
- | ^ UART ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ |
| Yes | No | No | No | No | | | Yes | No | No | No | No | | ||
Line 32: | Line 32: | ||
===== Building and programming the Bootloader ===== | ===== Building and programming the Bootloader ===== | ||
- | Before the bootloader can be used, it needs to be built and programmed into the STM32F091RC's internal flash memory. The steps in this section only need to be done once. | + | Before the bootloader can be used, it needs to be built and programmed into the STM32G071RB's internal flash memory. The steps in this section only need to be done once. |
Set the project as the active project in Eclipse. This is achieved by clicking the **Boot** project in the //Project Explorer// to select it. Next, select //Project -> Rebuild Project// from the menu to compile all the bootloader sources and link them together into the final executable. | Set the project as the active project in Eclipse. This is achieved by clicking the **Boot** project in the //Project Explorer// to select it. Next, select //Project -> Rebuild Project// from the menu to compile all the bootloader sources and link them together into the final executable. | ||
- | The bootloader program is now ready to be programmed into the internal flash memory of the STM32F091RC microcontroller. Make sure the Nucleo-F091RC board is connected to your PC via a USB cable. Next, select //Run -> Debug// from the menu to flash the bootloader program. This will launch the Debug perspective in Eclipse. Once done, you can start the bootloader program by selecting //Run -> Resume// from the menu. | + | The bootloader program is now ready to be programmed into the internal flash memory of the STM32G071RB microcontroller. Make sure the Nucleo-G071RB board is connected to your PC via a USB cable. Next, select //Run -> Debug// from the menu to flash the bootloader program. This will launch the Debug perspective in Eclipse. Once done, you can start the bootloader program by selecting //Run -> Resume// from the menu. |
Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | ||
- | * \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_TrueStudio\**Boot**\Debug\**openblt_stm32f091.elf** | + | * \Target\Demo\ARMCM0_STM32G0_Nucleo_G071RB_TrueStudio\**Boot**\Debug\**openblt_stm32g071.elf** |
- | * \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_TrueStudio\**Boot**\Debug\**openblt_stm32f091.srec** | + | * \Target\Demo\ARMCM0_STM32G0_Nucleo_G071RB_TrueStudio\**Boot**\Debug\**openblt_stm32g071.srec** |
Line 50: | Line 50: | ||
The output file is | The output file is | ||
- | * \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_TrueStudio\**Prog**\Debug\**demoprog_stm32f091.srec** | + | * \Target\Demo\ARMCM0_STM32G0_Nucleo_G071RB_TrueStudio\**Prog**\Debug\**demoprog_stm32g071.srec** |
===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
- | To download the demo program \Target\Demo\ARMCM0_STM32F0_Nucleo_F091RC_TrueStudio\**Prog**\Debug\**demoprog_stm32f091.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | + | To download the demo program \Target\Demo\ARMCM0_STM32G0_Nucleo_G071RB_TrueStudio\**Prog**\Debug\**demoprog_stm32g071.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: |
+ | |||
+ | * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] | ||
- | * [[manual:uart_demo|Firmware updates using the UART communication interface]] | ||
- | * [[manual:can_demo|Firmware updates using the CAN communication interface]] | ||