This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
manual:demos:nucleo_l552ze_cubeide [2021/06/15 11:35] voorburg |
manual:demos:nucleo_l552ze_cubeide [2023/12/04 22:37] (current) voorburg [Supported firmware update interfaces] |
||
---|---|---|---|
Line 3: | Line 3: | ||
===== Supported firmware update interfaces ===== | ===== Supported firmware update interfaces ===== | ||
- | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ |
- | | Yes | Yes | Yes | No | No | | + | | Yes | Yes | Yes | No | No | No | |
===== Development Environment ===== | ===== Development Environment ===== | ||
Line 32: | Line 32: | ||
===== Building and programming the Bootloader ===== | ===== Building and programming the Bootloader ===== | ||
- | Before the bootloader can be used, it needs to be built and programmed into the STM32F429ZI's internal flash memory. The steps in this section only need to be done once. | + | Before the bootloader can be used, it needs to be built and programmed into the STM32L552ZE's internal flash memory. The steps in this section only need to be done once. |
- Set the project as the active project in Eclipse. This is achieved by clicking the **Boot** project in the //Project Explorer// to select it. | - Set the project as the active project in Eclipse. This is achieved by clicking the **Boot** project in the //Project Explorer// to select it. | ||
- | - Delete the file \Target\Demo\ARMCM33_STM32L5_Nucleo_L552ZE_CubeIDE\**Boot**\Debug\**openblt_stm32l552.elf**. | ||
- Next, right-click the **Boot** project in the //Project Explorer// and select //Refresh// from the popup menu. | - Next, right-click the **Boot** project in the //Project Explorer// and select //Refresh// from the popup menu. | ||
- Finally, right-click the **Boot** project in the //Project Explorer// and select //Build Project// from the popup menu to compile all the bootloader sources and link them together into the final executable. | - Finally, right-click the **Boot** project in the //Project Explorer// and select //Build Project// from the popup menu to compile all the bootloader sources and link them together into the final executable. | ||
Line 49: | Line 48: | ||
- Set the project as the active project in Eclipse. This is achieved by clicking the **Prog** project in the //Project Explorer// to select it. | - Set the project as the active project in Eclipse. This is achieved by clicking the **Prog** project in the //Project Explorer// to select it. | ||
- | - Delete the file \Target\Demo\ARMCM33_STM32L5_Nucleo_L552ZE_CubeIDE\**Prog**\Debug\**demoprog_stm32l552.elf**. | ||
- Next, right-click the **Prog** project in the //Project Explorer// and select //Refresh// from the popup menu. | - Next, right-click the **Prog** project in the //Project Explorer// and select //Refresh// from the popup menu. | ||
- Finally, right-click the **Prog** project in the //Project Explorer// and select //Build Project// from the popup menu to compile all the user program sources and link them together into the final executable. | - Finally, right-click the **Prog** project in the //Project Explorer// and select //Build Project// from the popup menu to compile all the user program sources and link them together into the final executable. | ||
Line 55: | Line 53: | ||
The output file is | The output file is | ||
- | * \Target\Demo\ARMCM33_STM32L5_Nucleo_L552ZE_CubeIDE\**Prog**\Debug\**demoprog_stm32f429.srec** | + | * \Target\Demo\ARMCM33_STM32L5_Nucleo_L552ZE_CubeIDE\**Prog**\Debug\**demoprog_stm32l552.srec** |
===== Firmware update procedure ===== | ===== Firmware update procedure ===== |