manual:demos:olimex_em32g880f128stk_crossworks
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
manual:demos:olimex_em32g880f128stk_crossworks [2012/03/02 19:15] voorburg |
manual:demos:olimex_em32g880f128stk_crossworks [2015/05/22 18:05] 127.0.0.1 external edit |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== ARM-CM3 EFM32 Olimex EM-32G880F128-STK Crossworks ====== | ====== ARM-CM3 EFM32 Olimex EM-32G880F128-STK Crossworks ====== | ||
| + | |||
| + | ===== Supported firmware update interfaces ===== | ||
| + | ^ UART ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | ||
| + | | Yes | No | No | No | No | | ||
| ===== Development Environment ===== | ===== Development Environment ===== | ||
| Line 22: | Line 26: | ||
| * \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_Crossworks\**Boot**\bin\**openbtl_olimex_efm32g880.srec** | * \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_Crossworks\**Boot**\bin\**openbtl_olimex_efm32g880.srec** | ||
| - | ===== Configuring Microboot ===== | + | ===== Building the Demo Program ===== |
| - | The Microboot utility needs to be configured to connect to the correct COM-port and to communication at the correct baudrate: | + | |
| - | + | ||
| - | * Start Microboot by double-clicking "\Host\**MicroBoot.exe**". | + | |
| - | * Click the "**Settings**"-button and select "**OpenBLT using UART**" from the dropdown box. | + | |
| - | * Click the "**Options**"-button to configure the communication parameters. | + | |
| - | * Select the PC's **COM-port** that the board is connected to. | + | |
| - | * Set the baudrate to **9600** bits/sec. | + | |
| - | + | ||
| - | Once you saved the settings by clicking the "**OK**"-button twice, you can close Microboot by clicking the "**Cancel**"-button on the main screen. Microboot is now ready for action! | + | |
| - | + | ||
| - | ===== Building and downloading the Demo Program ===== | + | |
| When using Rowley CrossWorks, simply open the project from within CrossWorks. The project file is located at: \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_Crossworks\**Prog**\ide\ | When using Rowley CrossWorks, simply open the project from within CrossWorks. The project file is located at: \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_Crossworks\**Prog**\ide\ | ||
| Line 39: | Line 32: | ||
| * \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_Crossworks\**Prog**\bin\**demoprog_olimex_efm32g880.srec** | * \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_Crossworks\**Prog**\bin\**demoprog_olimex_efm32g880.srec** | ||
| - | To download this **demoprog_olimex_efm32g880.srec** file to the remaining flash memory using the bootloader, start the **Microboot** program and click the "**Browse**"-button. Browse to the "\Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_Crossworks\**Prog**\bin\" directory and select the **demoprog_olimex_efm32g880.srec** file to start the download. | + | ===== Firmware update procedure ===== |
| - | + | To download the demo program \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_Crossworks\**Prog**\bin\**demoprog_olimex_efm32g880.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | |
| - | {{:manual:demos:olimex_em32g880f128stk_download.gif?|}} | + | |
| - | Once the download completed, the newly programmed software will be started by the bootloader. You can verify this by checking that the test "Olimex" blinks on the LCD. Congratulations! That's all there is to using the bootloader. | + | * [[manual:uart_demo|Firmware updates using the UART communication interface]] |
manual/demos/olimex_em32g880f128stk_crossworks.txt · Last modified: 2020/02/06 16:50 by voorburg
Page Tools
