manual:demos:olimex_em32g880f128stk_iar
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
manual:demos:olimex_em32g880f128stk_iar [2012/03/04 00:10] voorburg created |
manual:demos:olimex_em32g880f128stk_iar [2023/12/04 22:43] (current) voorburg [Supported firmware update interfaces] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== ARM-CM3 EFM32 Olimex EM-32G880F128-STK IAR ====== | ====== ARM-CM3 EFM32 Olimex EM-32G880F128-STK IAR ====== | ||
| + | |||
| + | ===== Supported firmware update interfaces ===== | ||
| + | |||
| + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ | ||
| + | | Yes | No | No | No | No | No | | ||
| ===== Development Environment ===== | ===== Development Environment ===== | ||
| Line 10: | Line 15: | ||
| To compile the demo programs you can use the [[http://www.iar.com/|IAR Embedded Workbench for ARM]] development environment. | To compile the demo programs you can use the [[http://www.iar.com/|IAR Embedded Workbench for ARM]] development environment. | ||
| - | |||
| ===== Building and programming the Bootloader ===== | ===== Building and programming the Bootloader ===== | ||
| + | |||
| Before the bootloader can be used, it needs to be built and programmed into the EFM32G880's internal flash memory. The steps in this section only need to be done once. | Before the bootloader can be used, it needs to be built and programmed into the EFM32G880's internal flash memory. The steps in this section only need to be done once. | ||
| Line 19: | Line 24: | ||
| The bootloader program is now ready to be programmed into the internal flash memory of the EFM32G880. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports: | The bootloader program is now ready to be programmed into the internal flash memory of the EFM32G880. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports: | ||
| - | * \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_IAR\**Boot**\bin\**openbtl_olimex_efm32g880.out** | + | * \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_IAR\**Boot**\bin\**openblt_olimex_efm32g880.out** |
| - | * \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_IAR\**Boot**\bin\**openbtl_olimex_efm32g880.srec** | + | * \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_IAR\**Boot**\bin\**openblt_olimex_efm32g880.srec** |
| - | ===== Configuring Microboot ===== | + | ===== Building the Demo Program ===== |
| - | The Microboot utility needs to be configured to connect to the correct COM-port and to communication at the correct baudrate: | + | |
| - | * Start Microboot by double-clicking "\Host\**MicroBoot.exe**". | ||
| - | * Click the "**Settings**"-button and select "**OpenBLT using UART**" from the dropdown box. | ||
| - | * Click the "**Options**"-button to configure the communication parameters. | ||
| - | * Select the PC's **COM-port** that the board is connected to. | ||
| - | * Set the baudrate to **9600** bits/sec. | ||
| - | |||
| - | Once you saved the settings by clicking the "**OK**"-button twice, you can close Microboot by clicking the "**Cancel**"-button on the main screen. Microboot is now ready for action! | ||
| - | |||
| - | ===== Building and downloading the Demo Program ===== | ||
| When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (lm3s6965.eww) is located at: \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_IAR\**Prog**\ide\. Once opened, select Project->Rebuild All from the menu to compile all the demo program sources and link the together into the final executable. | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (lm3s6965.eww) is located at: \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_IAR\**Prog**\ide\. Once opened, select Project->Rebuild All from the menu to compile all the demo program sources and link the together into the final executable. | ||
| The output file is | The output file is | ||
| + | |||
| * \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_IAR\**Prog**\bin\**demoprog_olimex_efm32g880.srec** | * \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_IAR\**Prog**\bin\**demoprog_olimex_efm32g880.srec** | ||
| - | To download this **demoprog_olimex_efm32g880.srec** file to the remaining flash memory using the bootloader, start the **Microboot** program and click the "**Browse**"-button. Browse to the "\Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_IAR\**Prog**\bin\" directory and select the **demoprog_olimex_efm32g880.srec** file to start the download. | + | ===== Firmware update procedure ===== |
| + | |||
| + | To download the demo program \Target\Demo\ARMCM3_EFM32_Olimex_EM32G880F128STK_IAR\**Prog**\bin\**demoprog_olimex_efm32g880.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | ||
| - | {{:manual:demos:olimex_em32g880f128stk_download.gif?|}} | + | * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] |
| - | Once the download completed, the newly programmed software will be started by the bootloader. You can verify this by checking that the test "Olimex" blinks on the LCD. Congratulations! That's all there is to using the bootloader. | ||
manual/demos/olimex_em32g880f128stk_iar.1330816253.txt.gz · Last modified: 2019/09/24 22:13 (external edit)
Page Tools
