User Tools

Site Tools


manual:demos:olimex_stm32p103

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:demos:olimex_stm32p103 [2011/11/26 11:47]
voorburg
manual:demos:olimex_stm32p103 [2019/09/24 22:12] (current)
Line 2: Line 2:
  
 ===== Development Environment ===== ===== Development Environment =====
-{{:​manual:​demos:​olimex_stm32p103.gif?​direct&200 |}}+ 
 +{{:​manual:​demos:​olimex_stm32p103.gif?​200 |}} 
 This demo is targeted towards the [[http://​olimex.com/​dev/​stm32-p103.html|Olimex STM32P103]] board, with 128 kB internal Flash EEPROM and 20 kB internal RAM. This demo is targeted towards the [[http://​olimex.com/​dev/​stm32-p103.html|Olimex STM32P103]] board, with 128 kB internal Flash EEPROM and 20 kB internal RAM.
  
Line 11: Line 13:
  
 ===== Building and programming the Bootloader ===== ===== Building and programming the Bootloader =====
-Before the bootloader can be used, it needs to be built and programmed into the LPC2294's internal flash memory. The steps in this section only need to be done once.+Before the bootloader can be used, it needs to be built and programmed into the STM32F103's internal flash memory. The steps in this section only need to be done once.
  
 ==== GCC ==== ==== GCC ====
-Batch files are added to aid in building the software program. First clean the bootloader program by double-clicking the file "​\Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_GCC\**Boot**\cmd\**clean.bat**"​. Next, build the bootloader program by double-clicking the file "​\Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_GCC\**Boot**\cmd\**build.bat**"​. The output should look like:+Batch files are added to aid in building the software program. First clean the bootloader program by double-clicking the file "​\Target\Demo\ARMCM3_STM32_Olimex_STM32P103_GCC\**Boot**\cmd\**clean.bat**"​. Next, build the bootloader program by double-clicking the file "​\Target\Demo\ARMCM3_STM32_Olimex_STM32P103_GCC\**Boot**\cmd\**build.bat**"​. The output should look like:
 <​code>​ <​code>​
-+++ Assembling [cstart.o] 
 +++ Compiling [hooks.o] +++ Compiling [hooks.o]
 +++ Compiling [main.o] +++ Compiling [main.o]
 +++ Compiling [boot.o] +++ Compiling [boot.o]
 ... ...
-+++ Linking [openbtl_olimex_lpc_l2294_20mhz.elf]++++ Linking [openbtl_olimex_stm32p103.elf]
 ... ...
-+++ Build complete [openbtl_olimex_lpc_l2294_20mhz.hex]++++ Build complete [openbtl_olimex_stm32p103.srec]
 </​code>​ </​code>​
  
-The bootloader program is now ready to be programmed into the internal flash memory of the LPC2294. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports:+The bootloader program is now ready to be programmed into the internal flash memory of the STM32F103. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports:
  
-  * \Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_GCC\**Boot**\bin\**openbtl_olimex_lpc_l2294_20mhz.elf** +  * \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_GCC\**Boot**\bin\**openbtl_olimex_stm32p103.elf** 
-  * \Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_GCC\**Boot**\bin\**openbtl_olimex_lpc_l2294_20mhz.hex**+  * \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_GCC\**Boot**\bin\**openbtl_olimex_stm32p103.srec**
  
 ==== CrossWorks ==== ==== CrossWorks ====
-When using Rowley CrossWorks, simply open the project from within CrossWorks. The project file is located at: \Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_Crossworks\**Boot**\ide\+When using Rowley CrossWorks, simply open the project from within CrossWorks. The project file is located at: \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Boot**\ide\
  
-The bootloader program is now ready to be programmed into the internal flash memory of the LPC2294. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports:+The bootloader program is now ready to be programmed into the internal flash memory of the STM32F103. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports:
  
-  * \Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_Crossworks\**Boot**\bin\**openbtl_olimex_lpc_l2294_20mhz.elf** +  * \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Boot**\bin\**openbtl_olimex_stm32p103.elf** 
-  * \Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_Crossworks\**Boot**\bin\**openbtl_olimex_lpc_l2294_20mhz.srec**+  * \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Boot**\bin\**openbtl_olimex_stm32p103.srec**
  
 ===== Configuring Microboot ===== ===== Configuring Microboot =====
Line 45: Line 46:
   * Click the "​**Settings**"​-button and select "​**OpenBLT using UART**"​ from the dropdown box.   * Click the "​**Settings**"​-button and select "​**OpenBLT using UART**"​ from the dropdown box.
   * Click the "​**Options**"​-button to configure the communication parameters.   * Click the "​**Options**"​-button to configure the communication parameters.
-    * Select the PC's **COM-port** that the LPC-L2294 ​board is connected to.+    * Select the PC's **COM-port** that the board is connected to.
     * Set the baudrate to **57600** bits/sec.     * Set the baudrate to **57600** bits/sec.
  
Line 52: Line 53:
 ===== Building and downloading the Demo Program ===== ===== Building and downloading the Demo Program =====
 ==== GCC ==== ==== GCC ====
-Batch files are added to aid in building the demo program. First clean the demo program by double-clicking the file "​\Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_GCC\**Prog**\cmd\**clean.bat**"​. Next, build the demo program by double-clicking the file "​\Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_GCC\**Prog**\cmd\**build.bat**"​. The output should look like:+Batch files are added to aid in building the demo program. First clean the demo program by double-clicking the file "​\Target\Demo\ARMCM3_STM32_Olimex_STM32P103_GCC\**Prog**\cmd\**clean.bat**"​. Next, build the demo program by double-clicking the file "​\Target\Demo\ARMCM3_STM32_Olimex_STM32P103_GCC\**Prog**\cmd\**build.bat**"​. The output should look like:
 <​code>​ <​code>​
-+++ Assembling ​[cstart.o++++ Compiling ​[boot.c
-+++ Compiling [main.o]++++ Compiling [main.c]
 ... ...
-+++ Linking [demoprog_olimex_lpc_l2294_20mhz.elf]++++ Linking [demoprog_olimex_stm32p103.elf]
 ... ...
-+++ Build complete [demoprog_olimex_lpc_l2294_20mhz.sx]++++ Build complete [demoprog_olimex_stm32p103.srec]
 </​code>​ </​code>​
  
 The output file is The output file is
-  * \Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_GCC\**Prog**\bin\**demoprog_olimex_lpc_l2294_20mhz.sx**+  * \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_GCC\**Prog**\bin\**demoprog_olimex_stm32p103.srec**
  
 ==== CrossWorks ==== ==== CrossWorks ====
-When using Rowley CrossWorks, simply open the project from within CrossWorks. The project file is located at: \Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_Crossworks\**Prog**\ide\+When using Rowley CrossWorks, simply open the project from within CrossWorks. The project file is located at: \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Prog**\ide\
  
 The output file is The output file is
-  * \Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_Crossworks\**Prog**\bin\**demoprog_olimex_lpc_l2294_20mhz.srec**+  * \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Prog**\bin\**demoprog_olimex_stm32p103.srec**
  
-To download this **demoprog_olimex_lpc_l2294_20mhz.sx** (or .srec) ​file to the remaining flash memory using the bootloader, start the **Microboot** program and click the "​**Browse**"​-button. Browse to the "​\Target\Demo\ARM7_LPC2000_Olimex_LPC_L2294_GCC\**Prog**\bin\"​ directory and select the **demoprog_olimex_lpc_l2294_20mhz.sx** file to start the download. ​+To download this **demoprog_olimex_stm32p103.srec** file to the remaining flash memory using the bootloader, start the **Microboot** program and click the "​**Browse**"​-button. Browse to the "​\Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Prog**\bin\"​ directory and select the **demoprog_olimex_stm32p103.srec** file to start the download. ​
  
-{{:manual:lpc2000_download.png?|}}+{{:manual:demos:​olimex_stm32p103_download.gif?|}}
  
 Once the download completed, the newly programmed software will be started by the bootloader. You can verify this by checking that the status LED blinks. Congratulations! That's all there is to using the bootloader. Once the download completed, the newly programmed software will be started by the bootloader. You can verify this by checking that the status LED blinks. Congratulations! That's all there is to using the bootloader.
  
manual/demos/olimex_stm32p103.1322304424.txt.gz · Last modified: 2019/09/24 22:13 (external edit)