Differences

This shows you the differences between two versions of the page.

--- manual:demos:olimex_stm32p103_crossworks [2013/05/29 15:44]
voorburg
+++ manual:demos:olimex_stm32p103_crossworks [2020/02/06 16:25] (current)
voorburg
@@ Line 1: / Line 1: @@
 ====== ARM-CM3 STM32 Olimex STM32P103 Crossworks ======
+===== Supported firmware update interfaces =====
+^ RS232          ^ CAN             ^ USB          ^ TCP/IP       ^ SD-card      ^
+| Yes            | Yes             | No           | No           | Yes          |
 ===== Development Environment =====
@@ Line 10: / Line 15: @@
 To compile the demo programs you can use the [[http://www.rowley.co.uk/|Rowley Crossworks for ARM]] development environment.
 ===== Building and programming the Bootloader =====
 Before the bootloader can be used, it needs to be built and programmed into the STM32F103's internal flash memory. The steps in this section only need to be done once.
-When using Rowley CrossWorks, simply open the project from within CrossWorks. The project file is located at: \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Boot**\ide\
+When using Rowley CrossWorks, simply open the project from within CrossWorks. The project file is located at: \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_Crossworks\**Boot**\ide\
 The bootloader program is now ready to be programmed into the internal flash memory of the STM32F103. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports:
-  * \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Boot**\bin\**openbtl_olimex_stm32p103.elf**
+  * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_Crossworks\**Boot**\bin\**openblt_olimex_stm32p103.elf**
-  * \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Boot**\bin\**openbtl_olimex_stm32p103.srec**
+  * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_Crossworks\**Boot**\bin\**openblt_olimex_stm32p103.srec**
-===== Configuring Microboot =====
+===== Building the Demo Program =====
-The Microboot utility needs to be configured to connect to the correct COM-port and to communication at the correct baudrate:
-  * Start Microboot by double-clicking "\Host\**MicroBoot.exe**".
+When using Rowley CrossWorks, simply open the project from within CrossWorks. The project file is located at: \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_Crossworks\**Prog**\ide\
-  * Click the "**Settings**"-button and select "**OpenBLT using UART**" from the dropdown box.
-  * Click the "**Options**"-button to configure the communication parameters.
-    * Select the PC's **COM-port** that the board is connected to.
-    * Set the baudrate to **57600** bits/sec.
-Once you saved the settings by clicking the "**OK**"-button twice, you can close Microboot by clicking the "**Cancel**"-button on the main screen. Microboot is now ready for action!
-===== Building and downloading the Demo Program =====
-When using Rowley CrossWorks, simply open the project from within CrossWorks. The project file is located at: \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Prog**\ide\
 The output file is
-  * \Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Prog**\bin\**demoprog_olimex_stm32p103.srec**
-To download this **demoprog_olimex_stm32p103.srec** file to the remaining flash memory using the bootloader, start the **Microboot** program and click the "**Browse**"-button. Browse to the "\Target\Demo\ARMCM3_STM32_Olimex_STM32P103_Crossworks\**Prog**\bin\" directory and select the **demoprog_olimex_stm32p103.srec** file to start the download.
-{{:manual:demos:olimex_stm32p103_download.gif?|}}
-Once the download completed, the newly programmed software will be started by the bootloader. You can verify this by checking that the status LED blinks. Congratulations! That's all there is to using the bootloader.
+  * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_Crossworks\**Prog**\bin\**demoprog_olimex_stm32p103.srec**
-===== Firmware updates from SD-card =====
+===== Firmware update procedure =====
-In addition to the previously described update procedure with Microboot, the bootloader demo is configured for making firmware updates from an SD-card. The procedure is:
-  - Insert the SD-card into your PC and store the firmware file **demoprog_olimex_stm32p103.srec** on it.
+To download the demo program \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_Crossworks\**Prog**\bin\**demoprog_olimex_stm32p103.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:
-  - Insert the SD-card into the card holder on the microcontroller board.
-  - Reset the microcontroller to start the firmware update. Once done, the newly programmed firmware is automatically started.
-The bootloader demo is configured to output log messages to a serial terminal. This enables you to view the progress of the firmware update with a terminal program such as Putty. The communication settings are the same as those described above in section //Configuring Microboot//. Additionally, the log messages are written to a file called **bootlog.txt** on the SD-card, which can optionally be checked for verification purposes.
+  * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]]
+  * [[manual:can_demo|Firmware updates using the CAN communication interface]]
+  * [[manual:sdcard_demo|Firmware updates from SD-card]]
-{{:manual:demos:sdcard_firmware_update_logging.gif?|}}

OpenBLT Bootloader

User Tools

Site Tools

Differences

Page Tools