User Tools

Site Tools


manual:demos:olimex_stm32p103_gcc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
manual:demos:olimex_stm32p103_gcc [2016/10/27 22:59]
voorburg [Supported firmware update interfaces]
manual:demos:olimex_stm32p103_gcc [2019/09/24 22:12]
127.0.0.1 external edit
Line 1: Line 1:
 ====== ARM-CM3 STM32 Olimex STM32P103 GCC ====== ====== ARM-CM3 STM32 Olimex STM32P103 GCC ======
- 
- 
  
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
Line 7: Line 5:
 ^ UART           ^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^ ^ UART           ^ CAN             ^ USB          ^ TCP/​IP ​      ^ SD-card ​     ^
 | Yes            | Yes             | No           | No           | Yes          | | Yes            | Yes             | No           | No           | Yes          |
- 
- 
  
 ===== Development Environment ===== ===== Development Environment =====
- 
- 
  
 {{:​manual:​demos:​olimex_stm32p103.gif?​200 |}} {{:​manual:​demos:​olimex_stm32p103.gif?​200 |}}
- 
- 
  
 This demo is targeted towards the [[http://​olimex.com/​dev/​stm32-p103.html|Olimex STM32P103]] board, with 128 kB internal Flash EEPROM and 20 kB internal RAM. This demo is targeted towards the [[http://​olimex.com/​dev/​stm32-p103.html|Olimex STM32P103]] board, with 128 kB internal Flash EEPROM and 20 kB internal RAM.
  
 +To program the bootloader into the internal flash on the STM32F103 microcontroller,​ the [[http://​www.olimex.com/​dev/​arm-usb-tiny-h.html|Olimex ARM-USB-TINY-H]] JTAG interface was used in combination with [[http://​openocd.sourceforge.net/​|OpenOCD 0.4.0]]. However, this is not required if you have another means of programming the internal flash.
  
 +To build the demo programs you can use the [[https://​developer.arm.com/​open-source/​gnu-toolchain/​gnu-rm|GNU ARM Embedded]] toolchain.
  
-To program the bootloader into the internal flash on the STM32F103 microcontroller,​ the [[http://​www.olimex.com/​dev/​arm-usb-tiny-h.html|Olimex ARM-USB-TINY-H]] JTAG interface was used in combination with [[http://​openocd.sourceforge.net/​|OpenOCD 0.4.0]]. However, this is not required if you have another means of programming the internal flash.+===== Toolchain configuration =====
  
 +The demo programs are configured for building with a Makefile. Before attempting to perform a build, update the location of the toolchain binaries (i.e. //​arm-none-eabi-gcc//​) in the Makefile. It is set in variable **TOOL_PATH**. If the toolchain binaries are available on the path, then the **TOOL_PATH** variable can be left empty.
  
 +{{:​manual:​demos:​makefile_toolpath.png?​nolink&​|}}
  
-The demo programs are pre-configured for building with the {{:​manual:​arm-2013.11-24-arm-none-eabi.zip?​linkonly|Codesourcery G++ Lite}} (Target OS EABI) toolchain. Alternatively,​ you can use the [[manual:​demos:​gcc_arm_embedded|GCC ARM Embedded]] toolchain. 
  
 +It is assumed that tools such as GNU //make// and //rm// are installed and available on the path. For (Ubuntu) Linux users this can be achieved by running command: //sudo apt-get install build-essential//​. Windows users can install the [[https://​gnu-mcu-eclipse.github.io/​windows-build-tools/​|GNU MCU Eclipse Windows Build Tools]].
  
 ===== Building and programming the Bootloader ===== ===== Building and programming the Bootloader =====
Line 33: Line 29:
 Before the bootloader can be used, it needs to be built and programmed into the STM32F103'​s internal flash memory. The steps in this section only need to be done once. Before the bootloader can be used, it needs to be built and programmed into the STM32F103'​s internal flash memory. The steps in this section only need to be done once.
  
 +To build the bootloader, open a command prompt in directory **\Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\Boot\** and run the command:
  
- +<​code>​ 
-Batch files are added to aid in building the software program. First clean the bootloader program by double-clicking the file "​\Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Boot**\cmd\**clean.bat**"​. Next, build the bootloader program by double-clicking the file "​\Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Boot**\cmd\**build.bat**"​. ​The output ​should look like:+make clean all 
 +</​code>​ 
 +  
 +The expected ​output ​is:
  
 <​code>​ <​code>​
- 
 +++ Compiling [hooks.o] +++ Compiling [hooks.o]
- 
 +++ Compiling [main.o] +++ Compiling [main.o]
- 
 +++ Compiling [boot.o] +++ Compiling [boot.o]
- 
 ... ...
- 
 +++ Linking [openblt_olimex_stm32p103.elf] +++ Linking [openblt_olimex_stm32p103.elf]
- 
 ... ...
- 
 +++ Build complete [openblt_olimex_stm32p103.srec] +++ Build complete [openblt_olimex_stm32p103.srec]
- 
 </​code>​ </​code>​
- 
- 
  
 The bootloader program is now ready to be programmed into the internal flash memory of the STM32F103. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports: The bootloader program is now ready to be programmed into the internal flash memory of the STM32F103. Using your favorite programmer, flash the bootloader using one of the following files, depending on what file type your programmer supports:
- 
- 
  
   * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Boot**\bin\**openblt_olimex_stm32p103.elf**   * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Boot**\bin\**openblt_olimex_stm32p103.elf**
- 
   * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Boot**\bin\**openblt_olimex_stm32p103.srec**   * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Boot**\bin\**openblt_olimex_stm32p103.srec**
- 
- 
  
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-Batch files are added to aid in building ​the demo program. First clean the demo program by double-clicking the file "​\Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Prog**\cmd\**clean.bat**"​. Next, build the demo program by double-clicking the file "\Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Prog**\cmd\**build.bat**"​. The output should look like:+To build the user program, open a command prompt in directory ​**\Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\Prog\** ​and run the command:
  
 <​code>​ <​code>​
 +make clean all
 +</​code>​
 + 
 +The expected output is:
  
 +<​code>​
 +++ Compiling [boot.c] +++ Compiling [boot.c]
- 
 +++ Compiling [main.c] +++ Compiling [main.c]
- 
 ... ...
- 
 +++ Linking [demoprog_olimex_stm32p103.elf] +++ Linking [demoprog_olimex_stm32p103.elf]
- 
 ... ...
- 
 +++ Build complete [demoprog_olimex_stm32p103.srec] +++ Build complete [demoprog_olimex_stm32p103.srec]
- 
 </​code>​ </​code>​
- 
- 
  
 The output file is The output file is
  
   * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Prog**\bin\**demoprog_olimex_stm32p103.srec**   * \Target\Demo\ARMCM3_STM32F1_Olimex_STM32P103_GCC\**Prog**\bin\**demoprog_olimex_stm32p103.srec**
- 
- 
  
 ===== Firmware update procedure ===== ===== Firmware update procedure =====
manual/demos/olimex_stm32p103_gcc.txt · Last modified: 2023/12/04 22:20 by voorburg