manual:demos:olimexino_stm32_truestudio
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
manual:demos:olimexino_stm32_truestudio [2018/06/07 12:15] voorburg [Building and programming the Bootloader] |
manual:demos:olimexino_stm32_truestudio [2020/02/06 16:26] voorburg |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ===== Supported firmware update interfaces ===== | ===== Supported firmware update interfaces ===== | ||
| - | ^ UART ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ |
| | No | Yes | Yes | No | Yes | | | No | Yes | Yes | No | Yes | | ||
| Line 45: | Line 45: | ||
| ===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
| - | To build the user program, open a command prompt in directory **\Target\Demo\ARMCM3_STM32F1_Olimexino_STM32_GCC\Prog\** and run the command: | + | Set the project as the active project in Eclipse. This is achieved by clicking the **Prog** project in the //Project Explorer// to select it. Next, select //Project -> Rebuild Project// from the menu to compile all the user program sources and link them together into the final executable. |
| - | + | ||
| - | <code> | + | |
| - | make clean all | + | |
| - | </code> | + | |
| - | + | ||
| - | The expected output is: | + | |
| - | + | ||
| - | <code> | + | |
| - | +++ Cleaning build environment | + | |
| - | +++ Clean complete | + | |
| - | +++ Assembling [startup_stm32f10x_md.S] | + | |
| - | +++ Compiling [boot.c] | + | |
| - | +++ Compiling [main.c] | + | |
| - | ... | + | |
| - | +++ Linking [demoprog_olimexino_stm32.elf] | + | |
| - | ... | + | |
| - | +++ Build complete [demoprog_olimexino_stm32.srec] | + | |
| - | </code> | + | |
| The output file is | The output file is | ||
| - | * \Target\Demo\ARMCM3_STM32F1_Olimexino_STM32_GCC\**Prog**\bin\**demoprog_olimexino_stm32.srec** | + | * \Target\Demo\ARMCM3_STM32F1_Olimexino_STM32_TrueStudio\**Prog**\Debug\**demoprog_olimexino_stm32.srec** |
| ===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
| - | To download the demo program \Target\Demo\ARMCM3_STM32F1_Olimexino_STM32_GCC\**Prog**\bin\**demoprog_olimexino_stm32.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | + | To download the demo program \Target\Demo\ARMCM3_STM32F1_Olimexino_STM32_TrueStudio\**Prog**\Debug\**demoprog_olimexino_stm32.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: |
| * [[manual:can_demo|Firmware updates using the CAN communication interface]] | * [[manual:can_demo|Firmware updates using the CAN communication interface]] | ||
manual/demos/olimexino_stm32_truestudio.txt · Last modified: 2020/02/06 16:26 by voorburg
Page Tools
