manual:demos:s32k118_evb_iar
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
manual:demos:s32k118_evb_iar [2020/03/26 12:20] voorburg created |
manual:demos:s32k118_evb_iar [2023/12/04 22:38] voorburg [Supported firmware update interfaces] |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ===== Supported firmware update interfaces ===== | ===== Supported firmware update interfaces ===== | ||
| - | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ |
| - | | Yes | Yes | No | No | No | | + | | Yes | Yes | No | No | No | No | |
| ===== Development Environment ===== | ===== Development Environment ===== | ||
| Line 22: | Line 22: | ||
| Before the bootloader can be used, it needs to be built and programmed into the S32K118's internal flash memory. The steps in this section only need to be done once. | Before the bootloader can be used, it needs to be built and programmed into the S32K118's internal flash memory. The steps in this section only need to be done once. | ||
| - | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (s32k118.eww) is located at: \Target\Demo\ARMCM0_S32K14_S32K118EVB_IAR\**Boot**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the bootloader sources and link them together into the final executable. | + | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (s32k118.eww) is located at: \Target\Demo\ARMCM0_S32K11_S32K118EVB_IAR\**Boot**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the bootloader sources and link them together into the final executable. |
| The bootloader program is now ready to be programmed into the internal flash memory of the S32K118. Select //Project -> Download and Debug (Ctrl+D)// from the menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Go (F5)// from the menu. | The bootloader program is now ready to be programmed into the internal flash memory of the S32K118. Select //Project -> Download and Debug (Ctrl+D)// from the menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Go (F5)// from the menu. | ||
| Line 28: | Line 28: | ||
| Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | ||
| - | * \Target\Demo\ARMCM0_S32K14_S32K118EVB_IAR\**Boot**\bin\**openblt_s32k118.out** | + | * \Target\Demo\ARMCM0_S32K11_S32K118EVB_IAR\**Boot**\bin\**openblt_s32k118.out** |
| - | * \Target\Demo\ARMCM0_S32K14_S32K118EVB_IAR\**Boot**\bin\**openblt_s32k118.srec** | + | * \Target\Demo\ARMCM0_S32K11_S32K118EVB_IAR\**Boot**\bin\**openblt_s32k118.srec** |
| ===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
| - | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (s32k118.eww) is located at: \Target\Demo\ARMCM0_S32K14_S32K118EVB_IAR\**Prog**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable. | + | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (s32k118.eww) is located at: \Target\Demo\ARMCM0_S32K11_S32K118EVB_IAR\**Prog**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable. |
| The output file is | The output file is | ||
| - | * \Target\Demo\ARMCM0_S32K14_S32K118EVB_IAR\**Prog**\bin\**demoprog_s32k118.srec** | + | * \Target\Demo\ARMCM0_S32K11_S32K118EVB_IAR\**Prog**\bin\**demoprog_s32k118.srec** |
| ===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
| - | To download the demo program \Target\Demo\ARMCM0_S32K14_S32K118EVB_IAR\**Prog**\bin\**demoprog_s32k118.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | + | To download the demo program \Target\Demo\ARMCM0_S32K11_S32K118EVB_IAR\**Prog**\bin\**demoprog_s32k118.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: |
| * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] | * [[manual:rs232_demo|Firmware updates using the RS232 communication interface]] | ||
| * [[manual:can_demo|Firmware updates using the CAN communication interface]] | * [[manual:can_demo|Firmware updates using the CAN communication interface]] | ||
manual/demos/s32k118_evb_iar.txt · Last modified: 2023/12/04 22:38 by voorburg
Page Tools
