manual:demos:stm32f0_discovery_gcc
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
manual:demos:stm32f0_discovery_gcc [2016/10/24 11:43] voorburg [Building and programming the Bootloader] |
manual:demos:stm32f0_discovery_gcc [2016/10/24 11:45] voorburg |
||
|---|---|---|---|
| Line 27: | Line 27: | ||
| Before the bootloader can be used, it needs to be built and programmed into the STM32F051's internal flash memory. The steps in this section only need to be done once. | Before the bootloader can be used, it needs to be built and programmed into the STM32F051's internal flash memory. The steps in this section only need to be done once. | ||
| - | When using EmBitz, simply open the project file by double-clicking the file: \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_GCC\**Boot**\ide\**stm32f0.ebp** from the Windows Explorer. To build the bootloader, select //Build -> Rebuild all target files// from the program menu. | + | When using EmBitz, simply open the project file by double-clicking the file: \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_GCC\**Boot**\ide\**stm32f0.ebp** from the Windows Explorer. To build the bootloader, select //Build -> Rebuild all target files// from the program menu. |
| The bootloader program is now ready to be programmed into the internal flash memory of the STM32F051. Make sure the ST-Link Debugger Interface on the STM32F0-Discovery board is connected to your PC via a USB cable. Next, select //Debug -> Start Debug Session (F8)// from EmBitz's program menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Run (F5)// from the program's menu. | The bootloader program is now ready to be programmed into the internal flash memory of the STM32F051. Make sure the ST-Link Debugger Interface on the STM32F0-Discovery board is connected to your PC via a USB cable. Next, select //Debug -> Start Debug Session (F8)// from EmBitz's program menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Run (F5)// from the program's menu. | ||
| Line 39: | Line 39: | ||
| ===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
| - | When using EmBitz, simply open the project file by double-clicking the file: \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_GCC\**Prog**\ide\**stm32f0.ebp** from the Windows Explorer. To build the demo program, select //Build -> Rebuild all target files// from the program's menu. | + | When using EmBitz, simply open the project file by double-clicking the file: \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_GCC\**Prog**\ide\**stm32f0.ebp** from the Windows Explorer. To build the demo program, select //Build -> Rebuild all target files// from the program's menu. |
| The output file is | The output file is | ||
| - | * \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_GCC\**Prog**\bin\**demoprog_stm32f051.srec** | + | * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_GCC\**Prog**\bin\**demoprog_stm32f051.srec** |
| ===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
| - | To download the demo program \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_GCC\**Prog**\bin\**demoprog_stm32f051.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | + | To download the demo program \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_GCC\**Prog**\bin\**demoprog_stm32f051.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: |
| * [[manual:uart_demo|Firmware updates using the UART communication interface]] | * [[manual:uart_demo|Firmware updates using the UART communication interface]] | ||
manual/demos/stm32f0_discovery_gcc.txt ยท Last modified: 2023/12/04 22:18 by voorburg
Page Tools
