manual:demos:stm32f0_discovery_iar
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
manual:demos:stm32f0_discovery_iar [2016/04/29 23:06] voorburg [Building and programming the Bootloader] |
manual:demos:stm32f0_discovery_iar [2019/09/24 22:12] 127.0.0.1 external edit |
||
|---|---|---|---|
| Line 27: | Line 27: | ||
| Before the bootloader can be used, it needs to be built and programmed into the STM32F051's internal flash memory. The steps in this section only need to be done once. | Before the bootloader can be used, it needs to be built and programmed into the STM32F051's internal flash memory. The steps in this section only need to be done once. | ||
| - | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f0.eww) is located at: \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Boot**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the bootloader sources and link them together into the final executable. | + | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f0.eww) is located at: \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Boot**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the bootloader sources and link them together into the final executable. |
| The bootloader program is now ready to be programmed into the internal flash memory of the STM32F051. Make sure the ST-Link Debugger Interface on the STM32F0-Discovery board is connected to your PC via a USB cable. Next, select //Project -> Download and Debug (Ctrl+D)// from the menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Go (F5)// from the menu. | The bootloader program is now ready to be programmed into the internal flash memory of the STM32F051. Make sure the ST-Link Debugger Interface on the STM32F0-Discovery board is connected to your PC via a USB cable. Next, select //Project -> Download and Debug (Ctrl+D)// from the menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Go (F5)// from the menu. | ||
| Line 33: | Line 33: | ||
| Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | Alternatively, you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: | ||
| - | * \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Boot**\bin\**openblt_stm32f051.out** | + | * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Boot**\bin\**openblt_stm32f051.out** |
| - | * \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Boot**\bin\**openblt_stm32f051.srec** | + | * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Boot**\bin\**openblt_stm32f051.srec** |
| ===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
| - | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f0.eww) is located at: \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Prog**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable. | + | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f0.eww) is located at: \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Prog**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable. |
| The output file is | The output file is | ||
| - | * \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Prog**\bin\**demoprog_stm32f051.srec** | + | * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Prog**\bin\**demoprog_stm32f051.srec** |
| ===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
| - | To download the demo program \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Prog**\bin\**demoprog_stm32f051.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | + | To download the demo program \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Prog**\bin\**demoprog_stm32f051.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: |
| * [[manual:uart_demo|Firmware updates using the UART communication interface]] | * [[manual:uart_demo|Firmware updates using the UART communication interface]] | ||
manual/demos/stm32f0_discovery_iar.txt · Last modified: 2023/12/04 22:18 by voorburg
Page Tools
