User Tools

Site Tools


manual:demos:stm32f0_discovery_iar

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:demos:stm32f0_discovery_iar [2016/04/29 23:06]
voorburg [Building and programming the Bootloader]
manual:demos:stm32f0_discovery_iar [2019/09/24 22:12] (current)
Line 27: Line 27:
 Before the bootloader can be used, it needs to be built and programmed into the STM32F051'​s internal flash memory. The steps in this section only need to be done once. Before the bootloader can be used, it needs to be built and programmed into the STM32F051'​s internal flash memory. The steps in this section only need to be done once.
  
-When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f0.eww) is located at: \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Boot**\ide\. Once opened, select //​Project->​Rebuild All// from the menu to compile all the bootloader sources and link them together into the final executable.+When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f0.eww) is located at: \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Boot**\ide\. Once opened, select //​Project->​Rebuild All// from the menu to compile all the bootloader sources and link them together into the final executable.
  
 The bootloader program is now ready to be programmed into the internal flash memory of the STM32F051. Make sure the ST-Link Debugger Interface on the STM32F0-Discovery board is connected to your PC via a USB cable. Next, select //Project -> Download and Debug (Ctrl+D)// from the menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Go (F5)// from the menu. The bootloader program is now ready to be programmed into the internal flash memory of the STM32F051. Make sure the ST-Link Debugger Interface on the STM32F0-Discovery board is connected to your PC via a USB cable. Next, select //Project -> Download and Debug (Ctrl+D)// from the menu to flash the bootloader program. Once done, you can start the bootloader program by selecting //Debug -> Go (F5)// from the menu.
Line 33: Line 33:
 Alternatively,​ you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports: Alternatively,​ you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports:
  
-  * \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Boot**\bin\**openblt_stm32f051.out** +  * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Boot**\bin\**openblt_stm32f051.out** 
-  * \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Boot**\bin\**openblt_stm32f051.srec**+  * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Boot**\bin\**openblt_stm32f051.srec**
  
  
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f0.eww) is located at: \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Prog**\ide\. Once opened, select //​Project->​Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable.+When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f0.eww) is located at: \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Prog**\ide\. Once opened, select //​Project->​Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable.
  
 The output file is The output file is
  
-  * \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Prog**\bin\**demoprog_stm32f051.srec**+  * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Prog**\bin\**demoprog_stm32f051.srec**
  
  
 ===== Firmware update procedure ===== ===== Firmware update procedure =====
  
-To download the demo program \Target\Demo\ARMCM0_STM32_Discovery_STM32F051_IAR\**Prog**\bin\**demoprog_stm32f051.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:+To download the demo program \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_IAR\**Prog**\bin\**demoprog_stm32f051.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:
  
   * [[manual:​uart_demo|Firmware updates using the UART communication interface]]   * [[manual:​uart_demo|Firmware updates using the UART communication interface]]
  
manual/demos/stm32f0_discovery_iar.txt · Last modified: 2019/09/24 22:12 (external edit)