User Tools

Site Tools


manual:demos:stm32f0_discovery_truestudio

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
manual:demos:stm32f0_discovery_truestudio [2018/05/17 16:54]
voorburg [Workspace creation in TrueStudio]
manual:demos:stm32f0_discovery_truestudio [2018/05/17 16:57]
voorburg [Building the Demo Program]
Line 38: Line 38:
 ===== Building and programming the Bootloader ===== ===== Building and programming the Bootloader =====
  
-Before the bootloader can be used, it needs to be built and programmed into the STM32F051's internal flash memory. The steps in this section only need to be done once.+Before the bootloader can be used, it needs to be built and programmed into the STM32F051R8's internal flash memory. The steps in this section only need to be done once.
  
-To build the bootloader, open a command prompt ​in directory ​**\Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_GCC\Boot\** and run the command:+Set the project as the active project ​in Eclipse. This is achieved by clicking the **Boot** ​project in the //Project Explorer// to select it. Next, select //Project -> Rebuild Project// from the menu to compile all the bootloader sources ​and link them together into the final executable.
  
-<code> +The bootloader program is now ready to be programmed into the internal flash memory of the STM32F051R8 microcontroller. Make sure the STM32F0-Discovery board is connected to your PC via a USB cable. Next, select //Run -Debug// from the menu to flash the bootloader program. This will launch the Debug perspective in Eclipse. Once done, you can start the bootloader program by selecting //Run -Resume// from the menu.
-make clean all +
-</code> +
-  +
-The expected output is:+
  
-<​code>​ +Alternatively,​ you can use your favorite programmer to flash the bootloader using one of the following files, depending on what file type your programmer supports:
-+++ Cleaning build environment +
-+++ Clean complete +
-+++ Assembling [startup_stm32f0xx.S] +
-+++ Compiling [main.c] +
-+++ Compiling [hooks.c] +
-... +
-+++ Linking [openblt_stm32f051.elf] +
-... +
-+++ Build complete [openblt_stm32f051.srec] +
-</​code>​+
  
-The bootloader program is now ready to be programmed into the internal flash memory of the STM32F051Using your favorite programmer (i.e. OpenOCD or STM32 ST-Link utility), flash the bootloader using one of the following files, depending on what file type your programmer supports:+  * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_TrueStudio\**Boot**\Debug\**openblt_stm32f051.elf** 
 +  * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_TrueStudio\**Boot**\Debug\**openblt_stm32f051.srec**
  
-  * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_GCC\**Boot**\bin\**openblt_stm32f051.elf** 
-  * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_GCC\**Boot**\bin\**openblt_stm32f051.srec** 
  
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-To build the user program, open a command prompt ​in directory ​**\Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_GCC\Prog\** and run the command: +Set the project as the active project ​in Eclipse. This is achieved by clicking the **Prog** ​project in the //Project Explorer// to select itNext, select ​//Project -Rebuild Project// from the menu to compile all the user program sources and link them together into the final executable.
- +
-<​code>​ +
-make clean all +
-</code> +
-  +
-The expected output is: +
- +
-<​code>​ +
-+++ Cleaning build environment +
-+++ Clean complete +
-+++ Assembling [startup_stm32f0xx.S] +
-+++ Compiling [boot.c] +
-+++ Compiling [main.c] +
-... +
-+++ Linking [demoprog_stm32f051.elf] +
-... +
-+++ Build complete [demoprog_stm32f051.srec] +
-</code>+
  
 The output file is The output file is
  
-  * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_GCC\**Prog**\bin\**demoprog_stm32f051.srec** +  * \Target\Demo\ARMCM0_STM32F0_Discovery_STM32F051_TrueStudio\**Prog**\Debug\**demoprog_stm32f051.srec**
  
 ===== Firmware update procedure ===== ===== Firmware update procedure =====
manual/demos/stm32f0_discovery_truestudio.txt · Last modified: 2020/02/06 16:20 by voorburg