User Tools

Site Tools


manual:demos:stm32f3_discovery_gcc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
manual:demos:stm32f3_discovery_gcc [2018/06/11 15:42]
voorburg [Building and programming the Bootloader]
manual:demos:stm32f3_discovery_gcc [2023/12/04 22:25] (current)
voorburg [Supported firmware update interfaces]
Line 3: Line 3:
 ===== Supported firmware update interfaces ===== ===== Supported firmware update interfaces =====
  
-UART           ^ CAN             ​^ USB          ^ TCP/​IP ​      ​^ SD-card ​     ^ +RS232         ^ CAN            ^ USB         ​^ TCP/​IP ​     ^ SD-card ​     ​^ Modbus RTU   
-| No             ​| No              | Yes           ​| No           | No           |+| No            | No             ​| Yes         | No          ​| No           | No           |
  
 ===== Development Environment ===== ===== Development Environment =====
Line 56: Line 56:
 ===== Building the Demo Program ===== ===== Building the Demo Program =====
  
-Set the project as the active project ​in Eclipse. This is achieved by clicking the **Prog** ​project in the //Project Explorer// to select itNext, select ​//Project -Rebuild Project// from the menu to compile all the user program sources and link them together into the final executable.+To build the user program, open a command prompt ​in directory ​**\Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_GCC\Prog\** and run the command: 
 + 
 +<​code>​ 
 +make clean all 
 +</code> 
 +  
 +The expected output is: 
 + 
 +<​code>​ 
 ++++ Cleaning build environment 
 ++++ Clean complete 
 ++++ Assembling [startup_stm32f303xc.s] 
 ++++ Compiling [timer.c] 
 ++++ Compiling [main.c] 
 +... 
 ++++ Linking [demoprog_stm32f303.elf] 
 +... 
 ++++ Build complete [demoprog_stm32f303.srec] 
 +</code>
  
 The output file is The output file is
  
-  * \Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_TrueStudio\**Prog**\Debug\**demoprog_stm32f303.srec**+  * \Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_GCC\**Prog**\bin\**demoprog_stm32f303.srec** 
  
 ===== Firmware update procedure ===== ===== Firmware update procedure =====
  
-To download the demo program \Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_TrueStudio\**Prog**\Debug\**demoprog_stm32f303.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:+To download the demo program \Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_GCC\**Prog**\bin\**demoprog_stm32f303.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use:
  
   * [[manual:​usb_demo|Firmware updates using the USB communication interface]]   * [[manual:​usb_demo|Firmware updates using the USB communication interface]]
  
 For firmware updates via USB, keep in mind that the USB cable should be connected to the USB USER connector on the board and not the USB ST-LINK connector. For firmware updates via USB, keep in mind that the USB cable should be connected to the USB USER connector on the board and not the USB ST-LINK connector.
manual/demos/stm32f3_discovery_gcc.1528724539.txt.gz · Last modified: 2019/09/24 22:13 (external edit)