This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
manual:demos:stm32f3_discovery_iar [2018/06/11 22:20] voorburg [Building and programming the Bootloader] |
manual:demos:stm32f3_discovery_iar [2023/12/04 22:25] (current) voorburg [Supported firmware update interfaces] |
||
---|---|---|---|
Line 3: | Line 3: | ||
===== Supported firmware update interfaces ===== | ===== Supported firmware update interfaces ===== | ||
- | ^ UART ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ | + | ^ RS232 ^ CAN ^ USB ^ TCP/IP ^ SD-card ^ Modbus RTU ^ |
- | | No | No | Yes | No | No | | + | | No | No | Yes | No | No | No | |
===== Development Environment ===== | ===== Development Environment ===== | ||
Line 32: | Line 32: | ||
===== Building the Demo Program ===== | ===== Building the Demo Program ===== | ||
- | To build the user program, open a command prompt in directory **\Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_GCC\Prog\** and run the command: | + | When using IAR EWARM, simply open the workspace from within the Embedded Workbench. The workspace file (stm32f303.eww) is located at: \Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_IAR\**Prog**\ide\. Once opened, select //Project->Rebuild All// from the menu to compile all the demo program sources and link the together into the final executable. |
- | + | ||
- | <code> | + | |
- | make clean all | + | |
- | </code> | + | |
- | + | ||
- | The expected output is: | + | |
- | + | ||
- | <code> | + | |
- | +++ Cleaning build environment | + | |
- | +++ Clean complete | + | |
- | +++ Assembling [startup_stm32f303xc.s] | + | |
- | +++ Compiling [timer.c] | + | |
- | +++ Compiling [main.c] | + | |
- | ... | + | |
- | +++ Linking [demoprog_stm32f303.elf] | + | |
- | ... | + | |
- | +++ Build complete [demoprog_stm32f303.srec] | + | |
- | </code> | + | |
The output file is | The output file is | ||
- | * \Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_GCC\**Prog**\bin\**demoprog_stm32f303.srec** | + | * \Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_IAR\**Prog**\bin\**demoprog_stm32f303.srec** |
===== Firmware update procedure ===== | ===== Firmware update procedure ===== | ||
- | To download the demo program \Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_GCC\**Prog**\bin\**demoprog_stm32f303.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: | + | To download the demo program \Target\Demo\ARMCM4_STM32F3_Discovery_F303VC_IAR\**Prog**\bin\**demoprog_stm32f303.srec** using the bootloader, follow the instructions in the following links, depending on the communication interface you intend to use: |
* [[manual:usb_demo|Firmware updates using the USB communication interface]] | * [[manual:usb_demo|Firmware updates using the USB communication interface]] | ||
For firmware updates via USB, keep in mind that the USB cable should be connected to the USB USER connector on the board and not the USB ST-LINK connector. | For firmware updates via USB, keep in mind that the USB cable should be connected to the USB USER connector on the board and not the USB ST-LINK connector. |