manual:bootcommander
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
manual:bootcommander [2022/02/10 10:56] voorburg [Building on Windows with Microsoft Visual C++] |
manual:bootcommander [2023/12/04 22:48] (current) voorburg |
||
|---|---|---|---|
| Line 39: | Line 39: | ||
| * **-d=[name]** sets the name of the communication device. For example COM1 or /dev/ttyUSB0 (mandatory). | * **-d=[name]** sets the name of the communication device. For example COM1 or /dev/ttyUSB0 (mandatory). | ||
| * **-b=[value]** sets the communication speed in bits per second, as a 32-bit value (default = 57600). Supported values are: 9600, 19200, 38400, 57600, 115200. | * **-b=[value]** sets the communication speed in bits per second, as a 32-bit value (default = 57600). Supported values are: 9600, 19200, 38400, 57600, 115200. | ||
| + | |||
| + | Additional XCP on Modbus RTU settings (**xcp_mbrtu**): | ||
| + | * **-d=[name]** sets the name of the communication device. For example COM1 or /dev/ttyUSB0 (mandatory). | ||
| + | * **-b=[value]** sets the communication speed in bits per second, as a 32-bit value (default = 57600). Supported values are: 9600, 19200, 38400, 57600, 115200. | ||
| + | * **-pa=[value]** sets the UART parity bit configuration as a 8-bit value (default = 2). Supported values are: 0 (none), 1 (odd), 2 (even). | ||
| + | * **-sb=[value]** sets the UART stopbits configuration as a 8-bit value (default = 1). Supported values are: 1, 2. | ||
| + | * **-da=[value]** sets the destination address, i.e. the node ID of the receiver as a 8-bit value (default = 1). Supported values are: between 1 and 247. | ||
| Additional XCP on CAN settings (**xcp_can**): | Additional XCP on CAN settings (**xcp_can**): | ||
| Line 46: | Line 53: | ||
| * **lawicel_canusb** = Lawicel CANUSB. | * **lawicel_canusb** = Lawicel CANUSB. | ||
| * **vector_xldriver** = Vector XL Driver. | * **vector_xldriver** = Vector XL Driver. | ||
| + | * **ixxat_vcidriver** = Ixxat VCI Driver. | ||
| * **-c=[value]** sets the zero based index of the CAN channel if multiple CAN channels are supported for the CAN adapter, as a 32-bit value (default = 0). | * **-c=[value]** sets the zero based index of the CAN channel if multiple CAN channels are supported for the CAN adapter, as a 32-bit value (default = 0). | ||
| * **-b=[value]** sets the communication speed, a.k.a baudrate in bits per second, as a 32-bit value (default = 500000). Supported values: 1000000, 800000, 500000, 250000, 125000, 100000, 50000, 20000, 10000. | * **-b=[value]** sets the communication speed, a.k.a baudrate in bits per second, as a 32-bit value (default = 500000). Supported values: 1000000, 800000, 500000, 250000, 125000, 100000, 50000, 20000, 10000. | ||
| Line 72: | Line 80: | ||
| <code>sudo apt-get install cmake</code> | <code>sudo apt-get install cmake</code> | ||
| - | Note that BootCommander relies on the OpenBLT Host Library (LibOpenBLT) and links this one as a static library. Make sure you already [[manual:libopenblt#building_libopenblt_from_sources|built LibOpenBLT]], before you attempt to build BootCommander. | + | Note that BootCommander relies on the OpenBLT Host Library (LibOpenBLT) and some of the files that were generated when building LibOpenBLT. Therefore, make sure you already [[manual:libopenblt#building_libopenblt_from_sources|built LibOpenBLT]], before you attempt to build BootCommander. |
| ==== Building on Linux with GCC ==== | ==== Building on Linux with GCC ==== | ||
| Line 95: | Line 103: | ||
| Using the Command Prompt in Windows, set the working directory to **.\Host\Source\BootCommander\build** and type the command: | Using the Command Prompt in Windows, set the working directory to **.\Host\Source\BootCommander\build** and type the command: | ||
| <code> | <code> | ||
| - | cmake -A Win32 .. | + | cmake .. |
| </code> | </code> | ||
| Line 110: | Line 118: | ||
| ==== Building on Windows with MinGW ==== | ==== Building on Windows with MinGW ==== | ||
| - | This method assumes that the MinGW compiler toolchain is installed on your PC. The installer can be downloaded from https://sourceforge.net/projects/mingw-w64/. | + | This method assumes that the MinGW compiler toolchain is installed on your PC. A convenient way to install it, is by downloading the installer that bundles the Code::Blocks IDE together with MinGW. When using OpenBLT version 1.14 or newer, it is recommended to download the [[https://sourceforge.net/projects/codeblocks/files/Binaries/20.03/Windows/codeblocks-20.03mingw-setup.exe/download|64-bit installer version]], because the included **libopenblt.dll** file is 64-bit as well. Otherwise you can download the [[https://sourceforge.net/projects/codeblocks/files/Binaries/20.03/Windows/32bit/codeblocks-20.03-32bit-mingw-32bit-setup.exe/download|32-bit installer version]]. |
| Make sure the **.\bin** directory of the MinGW installation directory is added to your path in Windows. A quick way to verify that this is the case, run the following command from the Command Prompt in Windows and make sure the program could be found: | Make sure the **.\bin** directory of the MinGW installation directory is added to your path in Windows. A quick way to verify that this is the case, run the following command from the Command Prompt in Windows and make sure the program could be found: | ||
| Line 120: | Line 128: | ||
| <code> | <code> | ||
| - | cmake -G "MinGW Makefiles" .. | + | cmake -G "CodeBlocks - MinGW Makefiles" .. |
| mingw32-make | mingw32-make | ||
| </code> | </code> | ||
manual/bootcommander.1644487004.txt.gz ยท Last modified: 2022/02/10 10:56 by voorburg
Page Tools
